Pride Mobility INFMANU1206 manual O M F O R T a D J U S T M E N T S, Comfort Adjustments

Page 23

V . C O M F O R T A D J U S T M E N T S

COMFORT ADJUSTMENTS

After becoming familiar with your power chair’s operation, you may find the need to make some adjustments to increase your comfort, such as seat height and angle, armrest angle, foot platform height and angle, and controller position.

NOTE: If your power chair is equipped with a Synergy Seat or TRU-Balance Power Positioning System, refer to the information provided in separate manuals. If your power chair is equipped with a medium-back, a high- back, or a reclining seat, refer to the following information.

WARNING! The center of gravity of your power chair was factory set to a position that meets the needs of the demographic majority of users. Your authorized Quantum Rehab Provider has evaluated your power chair and made any necessary adjustments to suit your specific requirements. Do not change your seating configuration without first contacting Pride Mobility Products or your authorized Quantum Rehab Provider.

WARNING! Some power chair components are heavy. You may need assistance to lift or carry them. Please refer to the specifications table for specific component weights before you disassemble the power chair.

WARNING! Remove the occupant from the power chair before making any adjustments.

You may need the following to make comfort adjustments:

metric/standard hex key set metric/standard socket set and ratchet adjustable wrench

Seat Height and Angle Adjustment The seat is attached to the power base through the UMS. You can change the seat height by raising the

front and rear seat towers. If you raise or lower only

one set of towers (front or rear), you can also change Figure 14. Seat Latch Safety (Disengaged) the seat base angle (dump).

To change the seat height:

1.Turn off the power to the controller.

2.Unplug the controller connector(s) from the elec- tronics tray.

3.Flip up the seat latch safety. See figure 14.

4.Squeeze the seat latch and release the seat from the front trapeze bar.

5.Slide the seat forward and remove it from the power base.

6.Remove the quick-release pins from the seat tow- ers (front and rear). See figure 15.

7.Remove both trapeze bars from the seat towers.

8.Lift off the shroud.

9.Remove the ball detent pin from each of the four seat towers. See figure 15.

10.Move the seat towers up or down to the desired height.

TRAPEZE BARS

SEAT TOWER

QUICK-RELEASE PIN

BALL DETENT PIN

Figure 15. Seat Height Adjustment

Quantum Jazzy 1420 Series

www.pridemobility.com

23

Image 23
Contents Quantum Quick Reference Information F E T Y G U I D E L I N E SIII N T E N T SShipping and Delivery SafetyN T R O D U C T I O N PURCHASER’S AgreementS a F E T Y Product Safety SymbolsS a F E T Y S a F E T Y S a F E T Y Modifications Pre-Ride Safety CheckGeneral Guidelines Incline Information Weight LimitationsTire Inflation Cornering Information Freewheel ModeBraking Information To navigate up over a curb or stationary obstacle Inclement Weather PrecautionsPublic Streets and Roadways Outdoor Driving Surfaces Stationary Obstacles Steps, Curbs, etcLift/Elevation Products Stairs and EscalatorsDoors ElevatorsBatteries Positioning BeltsPrescription Drugs/Physical Limitations TransfersElectromagnetic and Radio Frequency Interference EMI/RFI Alcohol/SmokingI . Y O U R P O W E R C H a I R Quantum Jazzy 1420 Series Power ChairQuantum Jazzy 1420 Series Power Base Shroud Removed Active-Trac Suspension Electronics TrayTo operate the manual freewheel lever Manual Freewheel LeverA S S E M B L Y Initial AssemblySeat Installation Controller Installation To install the seatPower Elevating Seat Installation Optional To install the power seatTo change the seat height Comfort AdjustmentsYou may need the following to make comfort adjustments O M F O R T a D J U S T M E N T STo change the seat position Seat Position AdjustmentManual Recline Seatback Adjustment To adjust the seatback angleArmrest Height Adjustment High-Back with Headrest Adjustment OptionalSeatback Angle Adjustment Armrest Width AdjustmentTo change the controller position Controller PositionTo extend the controller To raise or lower the foot platform Foot Platform Angle AdjustmentTo adjust the foot platform angle Foot Platform Height AdjustmentAnti-Tip Wheels To adjust the anti-tip wheelsTo change the seat height through toggle switch Power Elevating Seat OptionalCharging the Batteries B a T T E R I E S a N D C H a R G I N GBatteries and Charging Frequently Asked Questions FAQs Battery Break-inInfrequent Use Why do my new batteries seem weak?How can I ensure maximum battery life? Daily UseWhat about shipping? How should I store my power chair and its batteries?What about public transportation? I . C a R E a N D M a I N T E N a N C E Care and MaintenanceShould your power chair come in contact with water TemperatureMonthly Checks Daily ChecksWeekly Checks To check the brakesYearly Checks Disposal of Your Power ChairCleaning Instructions Wheel ReplacementDrive Wheel Battery ReplacementTo replace the batteries Corrective MaintenanceSpecifications P E N D I X I Specification SQuantum/Jazzy 1420 Dimensions and Ground Clearance T E S T E S Page Product Serial # Quality Control Quantum Jazzy 1420 Series