Quantum 1121 3SP, 1121 3MP manual To install the seat, Controller Harness Routing Contour Seat

Page 19

I V . A S S E M B L Y

To install the seat:

1.Set the seat towers to the desired height. To change the seat height, see V. “Comfort Adjustments.”

2.Tilt the seat back, and slide the rear extrusion onto the rear trapeze bar.

3.Lower the front extrusion onto the front trapeze bar until the seat latches into place.

4.Flip the seat latch safety down.

WARNING! Make sure the seat latch safety is flipped down before using your power chair.

5.Install the controller into one of the armrests. See V. “Comfort Adjustments.”

6.Plug the controller harness into the connector on the electronics tray.

7.Route the harness to ensure that the harness cannot be pinched in the seat hinge. See figure 11 or 12.

8.Secure the controller harness to the armrest receiver with one or more wire ties.

MANDATORY! Prevent controller harness damage! Avoid routing the controller harness on the outside of the armrest pad. Route the harness under the armrest or toward the inside of the armrest pad. Use correct tie-down points for the controller harness to prevent the harness from getting caught in the drive tires, pinched in the seat frame, or damaged when passing through doorways.

WIRE TIES

Figure 11. Controller Harness Routing – Contour Seat

Figure 12. Controller Harness Routing – Synergy Seat

Quantum 1121 Series

www.pridemobility.com

19

Image 19

Contents Quantum Quick Reference Information F E T Y G U I D E L I N E SIII N T E N T SShipping and Delivery SafetyN T R O D U C T I O N PURCHASER’S AgreementS a F E T Y Product Safety SymbolsS a F E T Y General Guidelines Pre-Ride Safety CheckModifications Tire Inflation Weight LimitationsIncline Information Braking Information Freewheel ModeCornering Information Public Streets and Roadways Outdoor Driving Surfaces Inclement Weather PrecautionsStationary Obstacles Steps, Curbs, etc Lift/Elevation Products Stairs and EscalatorsDoors ElevatorsBatteries Positioning BeltsPrescription Drugs/Physical Limitations TransfersElectromagnetic and Radio Frequency Interference EMI/RFI Alcohol/SmokingI . Y O U R P O W E R C H a I R Quantum 1121 Series Power ChairActive-Trac Suspension Electronics TrayTo operate the dual manual freewheel levers Manual Freewheel LeverSeat Installation Initial AssemblyA S S E M B L Y Controller Harness Routing Contour Seat To install the seatO M F O R T a D J U S T M E N T S Comfort AdjustmentsYou may need the following to make comfort adjustments Seat Height and Seat Angle AdjustmentManual Recline Seatback Adjustment Seat Position AdjustmentArmrest Angle Adjustment Seatback Angle AdjustmentArmrest Width Adjustment Armrest Height AdjustmentFoot Platform Depth Adjustment Foot Platform Height AdjustmentController Position Anti-Tip Wheels Foot Platform Angle AdjustmentTo adjust the foot platform angle To adjust the anti-tip wheelsTo change the seat height through toggle switch Power Elevating Seat OptionalTo use the swivel feature Batteries and Charging B a T T E R I E S a N D C H a R G I N GCharging the Batteries Frequently Asked Questions FAQs Battery Break-inHow can I get maximum range or distance per charge? Why do my new batteries seem weak?„ Daily Use „ Infrequent UseWhat about shipping? How can I ensure maximum battery life?How should I store my power chair and its batteries? What about public transportation?I . C a R E a N D M a I N T E N a N C E Care and MaintenanceShould your power chair come in contact with water TemperatureMonthly Checks Daily ChecksWeekly Checks To check the brakesYearly Checks Disposal of Your Power ChairCleaning Instructions Wheel ReplacementDrive Wheel Battery ReplacementTerminal. See figure When to See Your Quantum Rehab Provider for ServiceCorrective Maintenance To replace the batteriesSpecifications P E N D I X I Specification SQuantum 1121 Series Dimensions and Ground Clearance T E S T E S Product Serial # Quality Control Quantum 1121 Series