Quantum 1121 3SP, 1121 3MP manual Controller Position, Foot Platform Height Adjustment

Page 23

V . C O M F O R T A D J U S T M E N T S

Controller Position

You can move the controller in toward or out away from the armrest, or change the position of the control- ler for either left-hand or right-hand use.

 

WARNING! Do not place the controller

CONTROLLER

 

harness so that it can be pinched in

BRACKET

 

the seat frame or the power base

 

 

frame.

SETSCREW

To extend the controller:

 

1.

Flip up the armrest so it is perpendicular to the floor.

 

2.

Loosen the setscrew on the controller bracket. See

 

 

figure 17.

 

3.

Slide the controller into or out of the armrest to the

 

 

desired position.

 

4.

Tighten the setscrew to secure the controller.

 

To change the controller position:

Figure 17. Controller Adjustment

1.

Turn off the power to the controller.

 

2.

Unplug the controller connector from the power base.

 

3.

Remove any wire ties securing the controller harness to the armrest.

4.

Flip up the armrest so it is perpendicular to the floor.

 

5.

Loosen the setscrew on the controller bracket.

 

6.

Slide the controller out of the armrest.

 

7.

Loosen the setscrew in the other armrest.

 

8.

Place the controller in the other armrest.

 

9.

Tighten the setscrew to secure the controller.

 

10.

Route the controller harness to the back of the power base and plug in the controller.

11.

Secure the controller harness to the armrest with wire ties.

NOTE: If your power chair is equipped with a Specialty Seat, Synergy Seat, or TRU-Balance Power Positioning System, refer to the supplemental information provided with your seating system.

Foot Platform Height Adjustment

The foot platform height is easily adjusted to one of several different heights.

To raise or lower the foot platform:

1.Remove the nuts and bolts from the foot platform bracket. See figure 18.

2.Raise or lower the foot platform to the desired height.

3.Reinstall the nuts and bolts into the foot platform bracket and tighten.

Foot Platform Depth Adjustment

To adjust the foot platform depth:

1.Remove the nuts and bolts from the foot platform bracket. See figure 18.

2.Move the foot platform in or out to the desired depth.

3.Reinstall the nuts and bolts into the foot platform bracket and tighten.

FOOT PLATFORM BRACKET

NUTS AND BOLTS

BALL DETENT PIN

Figure 18. Foot Platform Height Adjustment

Quantum 1121 Series

www.pridemobility.com

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Quantum Quick Reference Information F E T Y G U I D E L I N E SIII N T E N T SShipping and Delivery SafetyN T R O D U C T I O N PURCHASER’S AgreementS a F E T Y Product Safety SymbolsS a F E T Y Modifications Pre-Ride Safety CheckGeneral Guidelines Incline Information Weight LimitationsTire Inflation Cornering Information Freewheel ModeBraking Information Stationary Obstacles Steps, Curbs, etc Inclement Weather PrecautionsPublic Streets and Roadways Outdoor Driving Surfaces Lift/Elevation Products Stairs and EscalatorsDoors ElevatorsBatteries Positioning BeltsPrescription Drugs/Physical Limitations TransfersElectromagnetic and Radio Frequency Interference EMI/RFI Alcohol/SmokingI . Y O U R P O W E R C H a I R Quantum 1121 Series Power ChairActive-Trac Suspension Electronics TrayTo operate the dual manual freewheel levers Manual Freewheel LeverA S S E M B L Y Initial AssemblySeat Installation Controller Harness Routing Contour Seat To install the seatO M F O R T a D J U S T M E N T S Comfort AdjustmentsYou may need the following to make comfort adjustments Seat Height and Seat Angle AdjustmentManual Recline Seatback Adjustment Seat Position AdjustmentArmrest Angle Adjustment Seatback Angle AdjustmentArmrest Width Adjustment Armrest Height AdjustmentController Position Foot Platform Height AdjustmentFoot Platform Depth Adjustment Anti-Tip Wheels Foot Platform Angle AdjustmentTo adjust the foot platform angle To adjust the anti-tip wheelsTo use the swivel feature Power Elevating Seat OptionalTo change the seat height through toggle switch Charging the Batteries B a T T E R I E S a N D C H a R G I N GBatteries and Charging Frequently Asked Questions FAQs Battery Break-inHow can I get maximum range or distance per charge? Why do my new batteries seem weak?„ Daily Use „ Infrequent UseWhat about shipping? How can I ensure maximum battery life?How should I store my power chair and its batteries? What about public transportation?I . C a R E a N D M a I N T E N a N C E Care and MaintenanceShould your power chair come in contact with water TemperatureMonthly Checks Daily ChecksWeekly Checks To check the brakesYearly Checks Disposal of Your Power ChairCleaning Instructions Wheel ReplacementDrive Wheel Battery ReplacementTerminal. See figure When to See Your Quantum Rehab Provider for ServiceCorrective Maintenance To replace the batteriesSpecifications P E N D I X I Specification SQuantum 1121 Series Dimensions and Ground Clearance T E S T E S Product Serial # Quality Control Quantum 1121 Series
Top Page Image Contents