Pride Mobility 1103 ULTRA To charge the batteries using the onboard charger, Battery Break-in

Page 36

V I . B A T T E R I E S A N D C H A R G I N G

WARNING! If your off-board battery charger has not been tested and approved for outdoor use, then do not expose it to adverse or extreme weather conditions. If the battery charger is exposed to adverse or extreme weather conditions, then it must be allowed to adjust to the difference in environmental conditions before use indoors. Refer to the manual supplied with the battery charger for more information.

To charge the batteries using the onboard charger:

1.Position the rear of your power chair close to a standard electrical outlet.

2.Be certain the controller power is turned off and the freewheel levers are in the engaged position. See III. “Your Power Chair.”

3.Plug the charger power cord into the charger power cord receptacle on the power base, then into the electrical outlet.

NOTE: The power chair incorporates an inhibit function that disables the power chair when the charger is plugged into an electrical outlet.

4.We recommend you charge the batteries for 8 to 14 hours. As the batteries charge, the ammeter needle slowly drops to 0.

NOTE: The ammeter indicates how much charge is needed to fully charge the batteries. As the batteries charge, the ammeter needle slowly drops to 0. When the batteries are fully charged, the needle vibrates on or about the 0 mark on the ammeter.

5.When your power chair’s batteries are fully charged, disconnect the charger power cord, wind up the cord, and store it in a safe place.

To charge the batteries using the optional off-board charger:

1.Position the front of your power chair next to a standard electrical outlet.

2.Be certain the controller power is turned off and the freewheel levers are in the engaged position. See III. “Your Power Chair.”

3.Plug the off-board charger into the off-board charger/programming socket on the controller.

4.Plug the off-board charger into the electrical outlet.

NOTE: If it is a Pride off-board charger, then there are two lights in it. The red light indicates that power to the off-board charger is on. The green light indicates that the batteries are fully charged. If it is not a Pride off- board charger, then follow the instructions supplied by the manufacturer.

5. When the batteries are fully charged, unplug the off-board charger from the electrical outlet and then from the controller.

Battery Break-in

To break in new batteries for maximum efficiency:

1.Fully recharge any new battery prior to its initial use. This brings the battery up to about 90% of its peak performance level.

2.Operate your power chair throughout the house and yard. Move slowly at first, and do not travel too far until you become accustomed to the controls and break in the batteries.

3.Give the batteries another full charge of 8 to 14 hours and operate your power chair again. The batteries will now perform at over 90% of their potential.

4.After four or five charging cycles, the batteries will top off at 100% charge and last for an extended period.

36

www.pridemobility.com

Jazzy 1103 Ultra

Page 35 Page 37
Image 36
Page 35 Page 37
Contents How a Power Chair should Feel F E T Y G U I D E L I N E S Quick Reference InformationN T E N T S IIISafety N T R O D U C T I O NPURCHASER’S Agreement Shipping and DeliveryPride Owners Club Product Safety Symbols S a F E T YS a F E T Y S a F E T Y S a F E T Y Pre-Ride Safety Check General GuidelinesModifications Weight Limitations Tire InflationIncline Information Freewheel Mode Braking InformationCornering Information Inclement Weather Precautions Public Streets and Roadways Outdoor Driving SurfacesStationary Obstacles Steps, Curbs, etc Stairs and Escalators DoorsElevators Lift/Elevation ProductsBatteries Transfers Prescription Drugs/Physical LimitationsAlcohol/Smoking Electromagnetic and Radio Frequency Interference EMI/RFI I . Y O U R P O W E R C H a I R Jazzy 1103 UltraJazzy 1103 Ultra Specifications Jazzy 1103 Ultra Power Base Electrical ComponentsJazzy 1103 Ultra Electrical Components Manual Freewheel Levers To engage or disengage the drive motorsInitial Assembly A S S E M B L YSeat Installation To install the seatComfort Adjustments You may need the following to make comfort adjust- mentsO M F O R T a D J U S T M E N T S To change the seat heightManual Recline Seatback Adjustment To adjust the recline angleSeat Position To change the positionSeatback Angle Adjustment Armrest Width AdjustmentArmrest Angle Adjustment Armrest Height AdjustmentController Position To extend the controllerTo change the controller position Foot Platform Height Adjustment Foot Platform Depth AdjustmentFoot Platform Angle Adjustment To adjust the foot platform angleTo adjust the SFR length Swing-away FootrestsElevating Leg Rests Heavy Duty Drop-in Leg RestsTo adjust the anti-tip wheels Anti-Tip WheelsPower Elevating Seat System Standard Power Elevating Seat Operation To operate the power elevating seatTo use the swivel feature B a T T E R I E S a N D C H a R G I N G Batteries and ChargingCharging the Batteries To charge the batteries using the onboard charger Battery Break-inTo break in new batteries for maximum efficiency Frequently Asked Questions FAQs Why do my new batteries seem weak? How can I ensure maximum battery life?How should I store my power chair and its batteries? What about public transportation?Care and Maintenance Should your power chair come in contact with waterTemperature I . C a R E a N D M a I N T E N a N C EDaily Checks Weekly ChecksTo check the brakes Monthly ChecksDisposal of Your Power Chair Cleaning and DisinfectionWheel Replacement Yearly ChecksBattery Replacement Jazzy 1103 Ultra Drive WheelTo replace the batteries When to See Your Authorized Pride Provider for Service Corrective MaintenanceI I . W a R R a N T Y Reconditioned Units Warranty Warranty ExclusionsService Checks and Warranty Service Exclusions also include components with damage caused byQuality Control Jazzy 1103 Ultra
Related manuals
Manual 55 pages 43.83 Kb
Top Page Image Contents