Pride Mobility 1103 ULTRA manual To replace the batteries

Page 43

V I I . C A R E A N D M A I N T E N A N C E

WARNING! Power chair batteries are heavy. See specifications table. If you are unable to lift that much weight, be sure to get help. Use proper lifting techniques and avoid lifting beyond your capacity.

WARNING! Do not mix or match new and old batteries. If you encounter a situation where one battery needs to be replaced, then replace both batteries. Refer to the specification table in this manual and the manual supplied with the battery charger for recommended type and capacities.

To replace the batteries:

1.Turn off the power to the controller.

2.Make sure that the power chair is in drive mode. See III. “Your Power Chair.”

3.Loosen the rear shroud fasteners. See figure 6.

4.Remove the rear shroud.

5.Unplug the battery connector. See figure 29.

6.Disconnect the wiring harness from the rear battery.

7.Disconnect the controller from the power pod. See figure 7.

8.Pull up on the friction lock lever and remove the seat.

9.Remove the retaining pin from the foot platform and lift the platform off of the power base. See figure 18.

10.Turn the yellow fastener and remove the center shroud. See figure 6.

11.Disconnect the wiring harness.

12.Remove the rear battery.

13.Slide the front battery tray forward.

14.Disconnect the wiring harness from the front battery.

15.Remove the front battery.

16.Place a new rear battery onto the power base. Make sure that the terminals are facing forward.

17.Place a new battery in the front of the battery tray. Make sure that the terminals are facing each other.

WARNING! Use only the quick disconnect harness supplied with your power chair. It has a thermal fuse on each lead.

18. Connect the wiring harnesses to the front battery. See figure 29.

WARNING! Make sure you tighten the fasteners so that the connections are secure.

19.Connect the wiring harnesses to the rear battery. See figure 29.

20.Slide the battery tray back into the power base.

NOTE: Make sure that the power pod is out of the way when reinstalling the batteries.

21.Place the center shroud back on top of the power base and secure the yellow fastener.

22.Reinstall the foot platform.

23.Reinstall the seat.

24.Reconnect the battery connector.

25.Reconnect the controller to the power pad.

26.Reinstall the rear shroud and tighten the fasteners.

27.Charge the batteries. See VI. “Batteries and Charging.”

Jazzy 1103 Ultra

www.pridemobility.com

43

Page 42 Page 44
Image 43
Page 42 Page 44
Contents How a Power Chair should Feel Quick Reference Information F E T Y G U I D E L I N E SIII N T E N T SShipping and Delivery SafetyN T R O D U C T I O N PURCHASER’S AgreementPride Owners Club S a F E T Y Product Safety SymbolsS a F E T Y S a F E T Y S a F E T Y General Guidelines Pre-Ride Safety CheckModifications Tire Inflation Weight LimitationsIncline Information Braking Information Freewheel ModeCornering Information Public Streets and Roadways Outdoor Driving Surfaces Inclement Weather PrecautionsStationary Obstacles Steps, Curbs, etc Lift/Elevation Products Stairs and EscalatorsDoors ElevatorsBatteries Prescription Drugs/Physical Limitations TransfersAlcohol/Smoking Electromagnetic and Radio Frequency Interference EMI/RFI Jazzy 1103 Ultra I . Y O U R P O W E R C H a I RJazzy 1103 Ultra Specifications Electrical Components Jazzy 1103 Ultra Power BaseJazzy 1103 Ultra Electrical Components To engage or disengage the drive motors Manual Freewheel LeversA S S E M B L Y Initial AssemblyTo install the seat Seat InstallationTo change the seat height Comfort AdjustmentsYou may need the following to make comfort adjust- ments O M F O R T a D J U S T M E N T STo change the position Manual Recline Seatback AdjustmentTo adjust the recline angle Seat PositionArmrest Height Adjustment Seatback Angle AdjustmentArmrest Width Adjustment Armrest Angle AdjustmentTo extend the controller Controller PositionTo change the controller position Foot Platform Depth Adjustment Foot Platform Height AdjustmentSwing-away Footrests Foot Platform Angle AdjustmentTo adjust the foot platform angle To adjust the SFR lengthHeavy Duty Drop-in Leg Rests Elevating Leg RestsAnti-Tip Wheels To adjust the anti-tip wheelsPower Elevating Seat System Standard To operate the power elevating seat Power Elevating Seat OperationTo use the swivel feature Batteries and Charging B a T T E R I E S a N D C H a R G I N GCharging the Batteries Battery Break-in To charge the batteries using the onboard chargerTo break in new batteries for maximum efficiency Frequently Asked Questions FAQs What about public transportation? Why do my new batteries seem weak?How can I ensure maximum battery life? How should I store my power chair and its batteries?I . C a R E a N D M a I N T E N a N C E Care and MaintenanceShould your power chair come in contact with water TemperatureMonthly Checks Daily ChecksWeekly Checks To check the brakesYearly Checks Disposal of Your Power ChairCleaning and Disinfection Wheel ReplacementJazzy 1103 Ultra Drive Wheel Battery ReplacementTo replace the batteries Corrective Maintenance When to See Your Authorized Pride Provider for ServiceI I . W a R R a N T Y Exclusions also include components with damage caused by Reconditioned Units WarrantyWarranty Exclusions Service Checks and Warranty ServiceQuality Control Jazzy 1103 Ultra
Related manuals
Manual 55 pages 43.83 Kb
Top Page Image Contents