Pride Mobility 1107 owner manual Storage, Disposal of Your Power Chair, Cleaning and Disinfection

Page 43

V I I I . C A R E A N D M A I N T E N A N C E

Storage

Your power chair should be stored in a dry place, free from temperature extremes. When storing, disconnect the batteries from the power chair. See VI. “Batteries and Charging.”

WARNING! If you fail to store the unit properly, the frame can rust and the electronics can be damaged.

Disposal of Your Power Chair

Your power chair must be disposed of according to applicable local and national statutory regulations. Contact your local waste disposal agency or Quantum Rehab Specialist for information on proper disposal of power chair packaging, metal frame components, plastic components, electronics, and batteries.

Cleaning and Disinfection

!Use a damp cloth and mild, non-abrasive cleanser to clean the plastic and metal parts of your power chair. Avoid using products that may scratch the surface of your power chair.

!If necessary, clean your product with an approved disinfectant. Make sure the disinfectant is safe for use on your product before application.

WARNING! Prevent personal injury and product damage! Follow all safety instructions for the proper use of the disinfectant before applying it to your product.

Wheel Replacement

If you have pneumatic tires and you have a flat tire, you can replace the tube. If your chair is equipped with a solid tire insert, then you must replace the entire wheel assembly. Replacement tires, tubes, and wheel assemblies are readily avail- able through your authorized Pride Provider.

WARNING! To avoid possible injury, be sure that the controller’s power is turned off and the power chair is not in freewheel mode before performing this procedure.

WARNING! Completely deflate the tire before attempting repair.

AXLE KEY
	AXLE
DRIVEWHEEL	SLOT
DRIVEWHEEL
WASHER
DRIVE WHEEL NUT

Figure 32. Jazzy 1107 Drive Wheel

		TIRE
	TUBE
		WHEEL
	FRONT RIM	HUB
	FRONT RIM	REAR RIM
	HALF	REAR RIM
		HALF
	NUTS
	WASHERS

Figure 33. Jazzy 1107 Drive Wheel Disassembled

Follow these easy steps for a quick and safe repair for both pneumatic and solid tires:

1.Turn off the power to the controller.

2.Set the power chair up on blocks.

3.If you are changing a pneumatic tire, completely deflate it before removing the wheel.

Jazzy 1107

www.pridemobility.com

43

Image 43

Contents Exeter, PA St. Catharines, on F E T Y G U I D E L I N E S III N T E N T SInformation Exchange SafetyN T R O D U C T I O N PURCHASER’S AgreementMy Authorized Pride Provider Pride Owners ClubS a F E T Y Product Safety SymbolsS a F E T Y Modifications Pre-Ride Safety CheckTire Inflation Weight LimitationsIncline Information Cornering Information Braking InformationOutdoor Driving Surfaces Doors Freewheel ModeStationary Obstacles Steps, Curbs, etc Public Streets and Roadways Stairs and EscalatorsMotor Vehicle Transport TransfersElevators Lift/Elevation ProductsReaching and Bending Inclement Weather PrecautionsPositioning Belts BatteriesElectromagnetic and Radio Frequency Interference EMI/RFI AlcoholJazzy I . Y O U R P O W E R C H a I RJazzy 1107 Power Base Electrical Components Jazzy 1107 SpecificationsJazzy 1107 Electrical Components Flight Controller Shown To engage or disengage the drive motors Manual Freewheel LeversA S S E M B L Y / D I S a S S E M B L Y Initial AssemblyTo install the seat initial installation Seat InstallationTo remove the seat To disassemble the power base Power Base DisassemblyBattery Box Removal and Frame Separation To change the seat height Comfort AdjustmentsSeat Height and Seat Angle Adjustment O M F O R T a D J U S T M E N T SSeat Position Seatback Angle AdjustmentManual Recline Seatback Adjustment Armrest Width AdjustmentQuick Release Fasteners Armrest Angle AdjustmentFoot Platform Height Adjustment Foot Platform Depth AdjustmentController Position Foot Platform Angle AdjustmentElevating Leg Rests Swing-away FootrestsMulti-Axis Foot Plates To change foot plate angle D To adjust the anti-tip wheelsTo change foot plate position B To change foot plate tilt CBatteries and Charging B a T T E R I E S a N D C H a R G I N GCharging the Batteries Frequently Asked Questions FAQs Battery Break-inInfrequent Use Why do my new batteries seem weak?How often must I charge the batteries? Daily UseWhat about shipping? How can I ensure maximum battery life?How should I store my power chair and its batteries? What about public transportation?Joystick I . O P E R a T I O NFlight Controller Flight consistsHorn Key Battery Condition MeterLock Mode On/Off KeySpeed Keys Sleep Mode If EnabledError Codes Error Code Probable Cause Possible SolutionVSI consists VSI Electronic ControllerSpeed/Profile Keys Red lights only lit or slow flash Charge batteries as soonLocking/Unlocking the VSI Actuator Connector OptionalController Connector Actuator Keys and Actuator Lights For Optional EquipmentThermal Rollback VSI Error CodesI I . C a R E a N D M a I N T E N a N C E Care and MaintenanceShould your power chair come in contact with water TemperatureMonthly Checks Daily ChecksWeekly Checks To check the brakesStorage Disposal of Your Power ChairCleaning and Disinfection Wheel ReplacementI I . C a R E a N D Battery ReplacementTo replace the batteries Corrective Maintenance When to See Your Authorized Pride Provider for ServiceW a R R a N T Y Exclusions also include components with damage caused by Reconditioned Units WarrantyWarranty Exclusions Service Checks and Warranty ServiceT E S T E S T E S Pride keeps a more detailed report on file at the factory Quality Control