Pride Mobility JET 3 owner manual To install the seat, Seat Latch Safety Latched

Page 21

I V . A S S E M B L Y

To install the seat:

1.Set the trapeze bars to the desired height. To change the trapeze bar height, see V. "Comfort Adjustments."

2.Tilt the seat back and slide the rear extrusion onto the rear trapeze bar. See figure 10.

3.Lower the front extrusion onto the front trapeze bar until the seat locks into place.

4.Flip the seat latch safety down. See figure 11.

WARNING! Make sure the seat latch safety is flipped down before using your power chair.

5.Install the controller into one of the armrests. See VI. "ComfortAdjustments."

6.Turn the rear shroud fasteners one-quarter turn in any direction. See figure 6.

7.Remove the rear shroud.

8.Plug the motor connectors, the charger inhibit connec- tor, and the battery connector into the power pod. See figure 7.

9.Reinstall the rear shroud. Turn the rear shroud fasten- ers one quarter turn in any direction.

10.Route the controller cable so that it cannot be pinched in the seat hinge.

11.Secure the controller cable to the armrest receiver with one or more wire ties.

SEAT LATCH SAFETY

Figure 11. Seat Latch Safety - Latched

Jet 3 Ultra

www.pridemobility.com

21

Image 21
Contents Stylish Design and Premium Performance F E T Y G U I D E L I N E S III N T E N T SN T R O D U C T I O N SafetyPURCHASER’S Agreement Information ExchangeMy Authorized Pride Provider Pride Owners ClubS a F E T Y Product Safety SymbolsS a F E T Y Modifications Pre-Ride Safety CheckWeight Limitations Tire InflationIncline Information Braking Information Cornering InformationMotor Vehicle Transport Outdoor Driving Surfaces Freewheel ModeStationary Obstacles Steps, Curbs, etc Stairs and EscalatorsObject you are transferring onto TransfersDoors ElevatorsPositioning Belts Inclement Weather PrecautionsPublic Streets and Roadways Reaching and Bending BatteriesElectromagnetic and Radio Frequency Interference EMI/RFI AlcoholJET 3 Ultra I . Y O U R P O W E R C H a I RJet 3 Ultra Power Base JET3ULTRASPECIFICATIONS Jet 3 Ultra Electrical Components Electrical ComponentsTo engage or disengage the drive motors Manual Freewheel LeversInitial Assembly Seat InstallationA S S E M B L Y Seat Latch Safety Latched To install the seatSeat Height and Seat Angle Adjustment Comfort AdjustmentsO M F O R T a D J U S T M E N T S To change the seat heightSeatback Angle Adjustment Manual Recline Seatback AdjustmentSeat Position Armrest Height Adjustment Armrest Width AdjustmentArmrest Angle Adjustment Controller PositionFoot Platform Height Adjustment Foot Platform Angle AdjustmentFoot Platform Depth Adjustment Swing-Away FootrestsAnti-Tip Wheels Elevating Leg Rests OptionalB a T T E R I E S a N D C H a R G I N G Batteries and ChargingCharging the Batteries Battery Break-in To charge the batteries using the onboard chargerFrequently Asked Questions FAQs Can I use a different battery charger?How often must I charge the batteries? Why do my new batteries seem weak?Daily Use Infrequent UseHow should I store my power chair and its batteries? How can I ensure maximum battery life?What about public transportation? What about shipping?GC Controller System I . O P E R a T I O NGC Controller system consists JoystickLock Mode Control PanelTo lock the controller Fault Codes Sleep ModeFault Code Probable Causes Possible Solution To unlock the controllerShould your power chair come in contact with water Care and MaintenanceTemperature I I . C a R E a N D M a I N T E N a N C EWeekly Checks Daily ChecksMonthly Checks Yearly ChecksDisposal of Your Power Chair Cleaning and DisinfectionWheel Replacement To replace the batteries Battery ReplacementJet 3 Ultra Battery Connections Corrective Maintenance When to See Your Authorized Pride Provider for ServiceW a R R a N T Y Implied Warranties Service Checks and Warranty ServiceT E S Power Chairs