Pride Mobility JET 3 owner manual To unlock the controller, Sleep Mode, Fault Codes

Page 33

V I I . O P E R A T I O N

NOTE: The battery gauge will flash the “locked” sequence. 1 LED will flash on and then off. 2 LEDs will flash on and then off. This sequence will continue until all five LEDs flash on and then off. The sequence will continue until the power is turned off or until the controller is unlocked.

To unlock the controller:

1.Press the on/off button to turn on the controller. The battery condition meter will flash the “locked” sequence.

2.Move the joystick to the full forward position until it beeps.

3.Move the joystick to the full rearward position until it beeps.

4.Release the joystick. There will be one long beep. The controller system is now unlocked.

Sleep Mode

The power chair controller features a sleep mode. Sleep mode is a built-in circuit that will automatically shut off the main power if the joystick is not moved in any direction for a period of time. This time factor is programmed into the controller. To restore power and continue, push any button on the control panel.

Fault Codes

The battery condition meter will flash fault codes when the controller system detects an abnormal condition is the electrical system. All of the battery condition meter LEDs will flash a number of times quickly, then pause, then flash again. The battery condition meter will continue to flash the fault codes until the problem is fixed. The table below identifies the individual fault codes. If any of these fault codes persist, contact your authorized Pride Provider.

Fault Code

Probable Cause(s)

Possible Solution

1

Flash

The batteries need charging.

Check the battery connections. If the battery

 

 

There is a bad connection to the batteries.

connections are good, then try charging the

 

 

 

batteries.

 

 

 

 

2

Flashes

There is a bad connection on the left motor.

Check the left motor connections and wiring

 

 

 

harnesses.

 

 

 

 

3

Flashes

The left motor has a short to a battery connection.

Contact your authorized Pride Provider.

 

 

 

 

4

Flashes

There is a bad connection on the right motor.

Check the right motor connections and wiring

 

 

 

harnesses.

 

 

 

 

5

Flashes

The right motor has a short to a battery connection.

Contact your authorized Pride Provider.

 

 

 

Rippling LEDs

The charge inhibit has been activated.

Make sure that the battery charger is not

 

 

 

connected to the power base.

 

 

 

 

7

Flashes

There is a joystick fault.

Make sure the joystick is in the center position

 

 

 

and then power off and on again.

 

 

 

 

8

Flashes

There is a control system fault.

Check power module and joystick module

 

 

 

connections and wiring.

 

 

 

 

9

Flashes

The park brakes have a bad connection.

Check the left and right motor connections and

 

 

 

wiring.

 

 

 

10 Flashes

An excessive voltage has been applied to

Check the battery connections.

 

 

the control system.

 

 

 

 

 

Jet 3 Ultra

www.pridemobility.com

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Stylish Design and Premium Performance F E T Y G U I D E L I N E S III N T E N T SN T R O D U C T I O N SafetyPURCHASER’S Agreement Information ExchangeMy Authorized Pride Provider Pride Owners ClubS a F E T Y Product Safety SymbolsS a F E T Y Modifications Pre-Ride Safety CheckWeight Limitations Tire InflationIncline Information Braking Information Cornering InformationMotor Vehicle Transport Outdoor Driving Surfaces Freewheel ModeStationary Obstacles Steps, Curbs, etc Stairs and EscalatorsObject you are transferring onto TransfersDoors ElevatorsPositioning Belts Inclement Weather PrecautionsPublic Streets and Roadways Reaching and Bending BatteriesElectromagnetic and Radio Frequency Interference EMI/RFI AlcoholJET 3 Ultra I . Y O U R P O W E R C H a I RJet 3 Ultra Power Base JET3ULTRASPECIFICATIONS Jet 3 Ultra Electrical Components Electrical ComponentsTo engage or disengage the drive motors Manual Freewheel LeversInitial Assembly Seat InstallationA S S E M B L Y Seat Latch Safety Latched To install the seatSeat Height and Seat Angle Adjustment Comfort AdjustmentsO M F O R T a D J U S T M E N T S To change the seat heightSeatback Angle Adjustment Manual Recline Seatback AdjustmentSeat Position Armrest Height Adjustment Armrest Width AdjustmentArmrest Angle Adjustment Controller PositionFoot Platform Height Adjustment Foot Platform Angle AdjustmentFoot Platform Depth Adjustment Swing-Away FootrestsAnti-Tip Wheels Elevating Leg Rests OptionalB a T T E R I E S a N D C H a R G I N G Batteries and ChargingCharging the Batteries Battery Break-in To charge the batteries using the onboard chargerFrequently Asked Questions FAQs Can I use a different battery charger?How often must I charge the batteries? Why do my new batteries seem weak?Daily Use Infrequent UseHow should I store my power chair and its batteries? How can I ensure maximum battery life?What about public transportation? What about shipping?GC Controller System I . O P E R a T I O NGC Controller system consists JoystickLock Mode Control PanelTo lock the controller Fault Codes Sleep ModeFault Code Probable Causes Possible Solution To unlock the controllerShould your power chair come in contact with water Care and MaintenanceTemperature I I . C a R E a N D M a I N T E N a N C EWeekly Checks Daily ChecksMonthly Checks Yearly ChecksDisposal of Your Power Chair Cleaning and DisinfectionWheel Replacement To replace the batteries Battery ReplacementJet 3 Ultra Battery Connections Corrective Maintenance When to See Your Authorized Pride Provider for ServiceW a R R a N T Y Implied Warranties Service Checks and Warranty ServiceT E S Power Chairs
Top Page Image Contents