Wiring Harness Installation

I I I . I N S T A L L A T I O N

NOTE: If your lift is equipped with an onboard battery, refer to “Onboard Battery Installation.”

6. Install the lift platform kit. Refer to the instructions supplied with the kit.

The wiring harness is approximately 25 ft. (7.62 meters) long and will accommodate most vehicles.

NOTE: You may wish to perform a practice run before installing the wiring harness. Route a piece of light rope (equivalent to the gage of the wiring harness) along the anticipated path observing contact points, potential rubbing/chafing points, and any sharp edges. Remove sharp edges with a fine grade file, then treat the steel with a rust inhibitor or metal sealant.

Follow these steps to route the Exterior Lift System wiring harness:

1.Route the lift system wiring harness (starting at the lift) through the interior of the vehicle until you reach the vehicle battery. See figure 7.You will typically find pass through points at the rear lighting assemblies, which will enable you to route the cable through the trunk and under the back seat.

2.Conceal the harness behind or under the interior panels of the vehicle (there should be existing holes). Be certain that the harness is protected with a rubber grommet when passing it through the metal panels and into the engine compartment.

3.Inside the engine compartment, secure the harness to the firewall and the inner fender with plastic wire ties. Use care not to cause abrasions to the wiring harness. It is important to secure the wiring harness at various points along its run of the vehicle.

WARNING! Do not cut or shorten the wiring harness. If the harness is too long, coil the excess wire and secure it with plastic wire ties.

4.Connect the red wire to the positive (+) terminal and the black (grounding) wire to the negative (-) terminal of the vehicle battery.

WARNING! Before operating the lift, inspect the wiring harness for proper routing and grounding. Improper routing can cause damage to the harness, and improper grounding can cause damage to the electrical system.

WIRING HARNESS	LIFT FRAME
GROUNDINGWIRE
LIFT WIRING CONNECTION

VEHICLE BATTERY

Figure 7.Wiring Harness Installation

Onboard Battery Installation

The optional onboard battery is designed for easy instal- lation as it does not require any wires to be routed through or under the vehicle.

Follow these steps to install the onboard battery:

1.Align the mounting holes in the battery case bracket with those in the accessory bracket located under the key switch tube. See figure 8.

2.Secure the battery case to the accessory bracket with the supplied hardware. See figure 8.

3.Insert the onboard battery into the battery case, making sure that the connector on the bottom of the battery aligns and fully connects with the mating connector inside the battery case.

4.Plug the battery cord on the bottom of the battery case into the mating connector running from the mo- tor. See figure 8.

ACCESSORY BRACKET

BATTERY CASE

BRACKET

Figure 8. Onboard Battery Installation

www.pridemobility.com

Exterior Lift System

www.pridemobility.com

Mobility Exterior LIft specifications

Pride Mobility has established itself as a leader in mobility solutions, and one of its standout products is the Mobility Exterior Lift. Designed for those who require assistance in transporting their mobility devices, this lift combines innovation with user-friendly features tailored to enhance the freedom of movement.

The Mobility Exterior Lift is crafted with both safety and convenience in mind. Its robust construction allows it to accommodate a variety of scooters and power wheelchairs. With a weight capacity typically ranging from 350 to 400 pounds, it ensures that most mobility devices can be securely loaded and transported without compromise.

One of the defining features of the Mobility Exterior Lift is its easy installation process. The lift is designed to fit onto a wide range of vehicles, including SUVs, vans, and trucks, making it a versatile option for users. It comes with a vehicle-specific mounting bracket that enhances the stability of the lift when in use. Additionally, the lift boasts a power assist function, allowing users to effortlessly raise and lower their mobility device with just the press of a button.

Safety is paramount, and the Mobility Exterior Lift is equipped with several safety features. The lift includes a secure locking mechanism that ensures the device remains in place during transport. Furthermore, the lift is designed to prevent accidental disengagement, reducing the risk of accidents while driving. The incorporation of reflective strips and bright colors also enhances visibility in low-light conditions, contributing to overall safety.

The technology behind the Mobility Exterior Lift is equally impressive. It utilizes hydraulic or electric systems that provide smooth and effortless operation. Users can control the lift from their vehicle’s interior, ensuring a seamless experience when loading or unloading their mobility device. The lift also features a manual override, giving users peace of mind in case of a power failure.

In terms of design, the Mobility Exterior Lift is built to withstand the elements. Its weather-resistant finish helps protect it from rust and corrosion, ensuring durability over time. The compact design minimizes the impact on the vehicle's aerodynamics and overall appearance while maximizing the functionality.

In summary, the Pride Mobility Mobility Exterior Lift represents an ideal solution for individuals seeking independence and ease of transport. Combining innovative technology with robust safety features and a user-friendly design, this lift empowers users to enjoy their outdoor experiences without hindrance. Whether for daily errands or leisurely outings, the Mobility Exterior Lift enhances mobility and freedom for its users.