Pride Mobility Traveller Plus HD ABS Plastic Shrouds, Motor Brushes, Nylon Lock NUT Replacement

Page 35

I X . C A R E A N D M A I N T E N A N C E

ABS PLASTIC SHROUDS

The shroud pieces are formed from durable ABS plastic and are coated with an advanced formula urethane paint. A light application of car wax will help the shrouds retain their high gloss.

AXLE BEARINGS AND THE MOTOR/TRANSAXLE ASSEMBLY

These items are all prelubricated, sealed, and require no subsequent lubrication.

MOTOR BRUSHES

The motor brushes are housed inside of the motor/transaxle assembly. They should be inspected periodically for wear by your authorized Pride Provider.

CONSOLE, CHARGER, AND REAR ELECTRONICS

!Keep these areas free of moisture.

!Allow these areas to dry thoroughly if they have been exposed to moisture before operating your Travel Scooter again.

NYLON LOCK NUT REPLACEMENT

Any nylon insert lock nut removed during the periodic maintenance, assembly, or disassembly of the Travel Scooter must be replaced with a new nut. Nylon insert lock nuts should not be reused as it may cause damage to the nylon insert, resulting in a less secure fit. Replacement nylon insert lock nuts are available at local hardware stores or through your authorized Pride Provider.

STORING YOUR TRAVEL SCOOTER

If you plan on not using your Travel Scooter for an extended period of time, it is best to:

1.Fully charge its batteries prior to storage.

2.Remove the battery pack from the Travel Scooter.

3.Store your Travel Scooter in a warm, dry environment.

4.Avoid storing your Travel Scooter where it will be exposed to temperature extremes.

WARNING! Always protect batteries from freezing temperatures and never charge a frozen battery. This damages the battery.

Batteries that are regularly and deeply discharged, infrequently charged, stored in extreme temperatures, or stored without a full charge may be permanently damaged, causing unreliable performance and limited service life. It is recommended that you charge the Travel Scooter batteries periodically throughout periods of prolonged storage to ensure proper performance.

You may wish to place several boards under the frame of your Travel Scooter to raise it off of the ground during periods of prolonged storage. This takes the weight off the tires and reduces the possibility of flat spots developing on the areas of the tires contacting the ground.

DISPOSAL OF YOUR SCOOTER

Your Travel Scooter must be disposed of according to applicable local and national statutory regulations. Contact your local waste disposal agency or authorized Pride Provider for information on proper disposal of packaging, metal frame components, plastic components, electronics, and batteries.

Elite Traveller Plus/Plus HD

www.pridemobility.com

35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Elite Traveller Plus F E T Y G U I D E L I N E S III N T E N T SShipping and Delivery SafetyN T R O D U C T I O N PURCHASER’S AgreementS a F E T Y Product Safety SymbolsS a F E T Y S a F E T Y Modifications Removable Parts PRE-RIDE Safety CheckGeneral Incline Information Weight LimitationsTire Inflation Maximum Recommended Incline Angle Braking Information Cornering InformationCorrect Curb Approach Outdoor Driving SurfacesDoors Inclement Weather PrecautionsFreewheel Mode Stairs and EscalatorsMotor Vehicle Transport ElevatorsLIFT/ELEVATION Products BatteriesPositioning Belts Reaching and BendingElectromagnetic and Radio Frequency Interference EMI/RFI Prescription DRUGS/PHYSICAL LimitationsALCOHOL/SMOKING To Move Backward, use either of the following I . Y O U R T R a V E L S C O O T E RTiller Console To Move Forward, use either of the followingRear Section Horn ButtonTiller Console Fuse Battery PackSee figure See figures 10, 11, To reinstall the shroud pieces, placeShroud Panels To remove the shroud panel piecesCharging Your Batteries Reading Your Battery VoltageB a T T E R I E S a N D C H a R G I N G What if my Travel Scooter’s batteries will not charge? Frequently Asked QuestionsFollow these easy steps to charge your batteries safely How does the charger work?How can I get maximum range or distance per charge? How can I ensure maximum battery life?Can I use a different charger? How often must I charge the batteries?How do I change a battery in my Travel Scooter? What type and size of battery should I use?What about public transport? Why do my new batteries seem weak?Getting Onto Your Travel Scooter PRE-RIDE Adjustments and ChecksP E R a T I O N Before Getting Onto Your Travel ScooterGetting OFF of Your Travel Scooter Power Down Timer FeatureC O M F O R T a D J U S T M E N T S Tiller Angle AdjustmentSeat Rotation Adjustment Armrest Width AdjustmentFront Storage Area Seat Height AdjustmentI . D I S a S S E M B L Y a N D a S S E M B L Y DisassemblyFrame Separation AssemblyDiagnostic Beep Codes I I . B a S I C TroubleshootingWhat if the main circuit breaker repeatedly trips? What if the Travel Scooter’s batteries won’t charge?C a R E a N D M a I N T E N a N C E Motor Brushes Axle Bearings and the MOTOR/TRANSAXLE AssemblyNylon Lock NUT Replacement ABS Plastic ShroudsA R R a N T Y Exclusions also include components with damage caused by P E N D I X I Specification S Travel Scooter Dimensions T E S T E S T E S INFMANU3231
Top Page Image Contents