![](/images/new-backgrounds/1137781/13778133x1.webp)
32 | X . S e t - u p & A d j u s t m e n t | |||
4. |
|
|
| |
|
| |||
the rear wheels of the chair are aligned. This will |
|
| ||
affect how well the chair will roll. Drag or resistance |
|
| ||
occurs in a wheelchair when the rear wheels are not |
|
| ||
properly aligned. |
|
|
| |
|
| |||
the eccentric axle sleeve. |
|
|
| |
5. Eccentric Axle Sleeve Adjustment |
|
|
| |
2° eccentric axle sleeves are standard on chair and are | Front of chair | Rear of chair | ||
used for | ||||
|
| |||
Sleeve Adjustments” for tightening procedures. |
|
| ||
a. To add 2° of camber: |
|
|
| |
1. Loosen axle sleeves. |
|
|
| |
2. Position axle sleeves with large lobes down (A). |
|
| ||
b. To subtract 2° of camber. |
|
|
| |
1. Loosen axle sleeves. |
|
|
| |
2. Position axle sleeves with large lobes up (B). |
|
| ||
c. Make sure both sleeves are aligned equally. |
|
| ||
G. CASTER FORKS |
|
|
|
1. Caster Wheel Replacement |
|
|
| A |
|
a. Loosen the bolt and remove the caster wheel and |
|
|
|
| |
|
|
| |||
|
|
|
|
| |
the two washers. |
|
|
|
|
|
b. Position new caster wheel into fork. |
|
|
|
|
|
c. Carefully position washer on each side of |
|
|
|
|
|
caster wheel. |
|
|
|
|
|
d. Insert bolt. Tighten securely. |
|
|
| B |
|
|
|
|
| ||
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
X . S e t - u p & A d j u s t m e n t | 33 | |
H. FOOTREST |
| |
NOTE– Use a torque setting of 100 in./lbs. when |
| |
| adjusting footplate. |
|
1. | Height Adjustment |
|
| a. Remove footrest bolt and slide footrest up or |
|
| down inside tube to correct position. |
|
| b. Tighten bolt securely. |
|
2. | Horizontal Adjustment |
|
| a. Loosen set screws at footrest receivers. |
|
| b. Slide footplate assembly to desired position. |
|
| c. Retighten screws. |
|
3. | Footplate Angle Adjustment |
|
| a. Loosen flathead screws. |
|
| b. Reposition footplate to desired angle and |
|
| retighten screws. |
|
I. INTEGRAL 5TH WHEEL
The Match Point comes standard with the 5th wheel. This increases rear stability.
Caster Height Adjustment for the Single Integral 5th wheel.
The
Each caster journal is equipped with four 1/8" thick
spacers (1). | Single Integral 5th Wheel |
a. To lower the casters remove desired spacers and position them on the bottom of caster journal (2).
b. To raise the height of the caster remove desired spacers and move to the top of the caster journal.
930469 Rev. A | 930469 Rev. A |