32 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| I | X | . |
| S e | t | - | U | p | , |
| A | d | j u | s | t | m | e | n | t |
| & |
| U | s | e |
|
I. JOYSTICK SWING-AWAY RETRACTABLE MOUNT (OPTIONAL)
The joystick is mounted with a mechanism which allows the control to be locked in a forward or retract- ed position using magnets.
Adjustment
a. To retract joystick, push outward on the inside of joystick.
b. Push joystick away from front of armrest until it
I X . S e t - U p , A d j u s t m e n t & U s e | 33 | ||
2. | Height Adjustment |
|
|
| a. Rotate release lever to stop. | 5 | 4 |
| b. Slide armrest pad up or down to desired | 3 | |
|
| ||
| height. |
| 1 |
| c. Return lever to locked position. |
| 7 |
| d. Push arm pad until upper armpost locks firmly | 2 | 8 |
| into place. | ||
|
|
| |
3. | Removing Armrest |
| 6 |
| a. Rotate release lever and remove the armrest. |
| 9 |
|
|
| |
4. | Replacing Armrest | ||
locks into retracted position.
c. To return to forward position, push joystick forward until it locks into place.
J. |
| |
The |
| |
C | ||
1. Installing Armrest | B | |
| ||
a. Insert front and rear posts into armrest receivers. |
| |
b. Engage levers (A and B) to secure armrest. | A | |
2. | ||
| ||
a. Disengage lever (A) so front post is able to come |
|
a. Slide armrest back into receiver. b. Return release lever to locked
position against armpost.
5. Adjusting Armrest Receiver Fit
To tighten or loosen the fit of the outer armpost in the receiver:
a. Loosen the four bolts on the sides of the receiver.
b. With the armrest in the receiver, squeeze the receiver to achieve the desired fit.
c. Tighten the four bolts.
6. Adjusting Inner Armpost Fit
1.Inner Arm Post
2.Receiver
3.Release Lever, Locked Position
4.Armrest Pad
5.Transfer Bar
6.Side Panel
7.Tension Adjustment Set Screw
8.Outer Arm Post
9.Receiver Adjustment Bolts
free. |
b. Armrest now has the ability to be flipped back |
without removal. |
3.Set-up for Removal
a.Disengage levers (A and B) so front and rear posts are able to come free.
b.Armrest can now be easily removed for transferring.
4.Height-Adjustment (option)
a.Release the upper securing lever (C).
b.Set at desired height
c.Return securing lever to locked position.
d.Move armrest up or down to allow armrest to snap into place
K.SINGLE POST HEIGHT-ADJUSTABLE ARMRESTS (OPTIONAL)
1.Installation
a.Slide the outer armpost into the receiver mount- ed to the wheel chair frame.
b.The armrest will automatically lock into place.
a. Two set screws are installed in the outer arm- post.
b. Turn the set screws in or out until the desired fit is achieved.
L. SEAT DEPTH
The seat depth can be adjusted in one inch increments.
1.Seat Frame Depth Adjustment
a.To adjust, remove the two bolts (C & D) from each side of the backrest pivot plate.
b.Reposition the backrest to the desired position.
c.Replace and retighten bolts on each side of the backrest pivot plate.
D |
C |
930475 Rev. A | 930475 Rev. A |