Invacare RWD, MWD, Arrow FWD service manual Arrow Fwd Model

Page 62

PROCEDURE 13

ELECTRONICS

Arrow Fwd Model

REMOVING.

E1. Remove the front shroud. Refer to REMOVING/IN-

L

STALLING FRONT SHROUD in PROCEDURE 17 of

this manual.

E

 

C2. Remove the counterweight. Refer to REMOVING/IN-

TSTALLING COUNTERWEIGHT in PROCEDURE 17

Rof this manual.

O3. Remove the battery box(es). Refer toINSTALLING/RE-

NMOVING GROUP 24 BATTERY BOXES in PROCE-

IDURE 9 of this manual.

C4. Disconnect the joystick cable from the top of the control-

Sler.

5.Disconnectthebatterywiringharnessandcontrollercon- nection.

6.Remove the two (2) mounting screws, spacers, wash- ers, and locknuts that secure the MKIV controller to the base frame. Set MKIV controller onto ground/floor.

7.Removethemountingscrewandspacerthatsecurethe top of right shock to the base frame.

8.Loosen, DO NOT remove, the mounting screw that se- curethebottomoftherightshocktothesuspensionarm.

9.Rotate top of right shock toward inside of the wheelchair.

10.Disconnect right hand motor/controller connection.

11.Rotate top of right shock back into position.

12.Loosely install mounting screw through top of shock and into base frame. DO NOT tighten at this point.

13.To disconnect left hand motor/controller connection, per- form STEPS 5-8 for opposite side of controller.

INSTALLING.

1.Connect left hand motor/controller connection of NEW controller.

2.Rotate top of left shock into position.

3.Secure top of left shock to base frame with washer and mounting screw. Torque to 360 - inch pounds.

4.Removemountingscrewandwasherthatsecurethetop of the right shock to the base frame.

5.Rotate shock toward inside of wheelchair.

6.Connect right hand motor/controller connection.

7.Rotate shock back into position.

8.Secure top of right shock to base frame with washer and mounting screw. Torque to 156 - inch pounds.

9.Torquethebottommountingscrewofeachshockto 160 - inch pounds.

10.Secure the MKIV controller to the base frame with the two(2)existingmountingscrews,spacers,washers, and locknuts.

11.Connect the joystick cable to the top of the controller.

12.Connect the battery wiring harness and controller con- nection.

13.Installthebatterybox(es).RefertoINSTALLING/REMOV- ING GROUP 24 BATTERY BOXES in PROCEDURE 9 of this manual.

14.Installthecounterweight.RefertoREMOVING/INSTALL- ING COUNTERWEIGHT in PROCEDURE 17 of this manual.

15.Install the front shroud. Refer to REMOVING/IN- STALLING FRONT SHROUD in PROCEDURE 17 of this manual.

Top Mounting

Locknut

Base Frame

Shock

Screw and

Washer

Spacer Washer

Mounting

Screw

Bottom Mounting

Controller

Screw

 

FIGURE 2 - REMOVING/INSTALLING MKIV CONTROLLER - ARROW FWD MODEL

62

Page 61 Page 63
Image 62
Page 61 Page 63
Contents Storm Series Wheelchairs R N I N G E C I a L T E STable of Contents Table of Contents Limited Warranty Specification S SpecificationsSpecifications Arrow FWD has a 400 lb. ratingProcedure General Guidelines Repair or Service InformationGeneral Guidelines Procedure MOTOR/GEARBOXSuspension Arm MWD ModelsFWD Models Located on insideBattery Charger Using Hydrometer to Check Battery Cells Lead Acid FigureTroubleshooting Procedure Field Load Test FigureNumber of Floating Balls Will Vary Motor Testing FigureProcedure Troubleshooting According to ChargeCap Motor Pin Motor Connector ELECTRO-MECHANICAL Parking Brake Testing FigureOhmmeter Motor Connector Cap Motor Pin Motor Connector OhmmeterHardware Torque Specifications Standard Seat FrameCaptains VAN Seat Adjustable Seat FrameHardware Torque Specifications Procedure Loctite and Torque to 75 in/lbs Torque to 156 in/lbsPneumatic with Flat-Free Wheel Halves Torque to Inch WheelsWheel Halves Pneumatic Wheel Halves 8 inch Torque to 18 in/lbsInch Wheels Wheel Halves Pneumatic with Flat-FreeTorque to 156 in/lbs Torque to 160 in/lbs Loctite Torque to 156 in/lbs 1020 in/lbsWheel Halves Torque to In/lbs Torque to 360 in/lbs Torque to 156 in/lbsReplacing Armrest Pads Captains VAN Seats Figure Arms ProcedureThis Procedure Includes the Following Replacing Captains VAN Seat Armrest Plate FigureReplacing Seat Positioning Y Strap Captains VAN Seats Replacing Back Upholstery FigureH O L S T E R Y M E Replacing Exact Same Size Standard Seat Frame REMOVING/INSTALLING Standard Seat Frame Subassembly FigureSeat Frame Procedure Mounting ScrewsInches Adjustable Seat Frame FigureSeat Frame Inch Inch deep InchesChanging Seat Depth Between 12 and 15- Inches Figure A T M ETorque to Standard Seat Frame Changing Seat Width Standard and Adjustable Seat FrameMounting Screws Torque to 75-inch pounds Seat Width Side Spacers CenterCoved Washer Component ReplacementPounds Center FrameRemoving Captains Van Seat INSTALLING/REMOVING Captains VAN Seat Assembly FigureInstalling Captains Van Seat Torque to Inch poundsAdjustable Frames Captains Van SeatRemove the seat cushion from the seat pan REMOVING/INSTALLING Seat PAN FigureInstalling Locknut Quick Release PinSeat Dump Seat Angle AdjustmentInstallation Orientation Replacing Seat Support Brackets Figure Base Frame ProcedureReplacing Seat Mounting Plates Figure S E M EMounting Screws Washer Seat Support Bracket BaseT-Nut Frame Procedure Base FrameReplacing Seat Support Bracket T-NUTS Figure Channel Cover Seat Support Mounting ScrewRWD and MWD Models Figure Replacing Battery Charger Bracket and T-NUTBattery Charg er Charger Connector Mount Arrow FWD Model FigureReplace the battery charger mount bracket and se REMOVING/INSTALLING Seat Stop Screws FigureMounting Screw Battery Charger Connector Tightensecurely Reverse A, 3B or 3CC K M E REMOVING/INSTALLING CJ Back Brackets FigureBack Frame Procedure CJ Bracket MountsHeavy Duty Models Procedure Back FrameChanging Back Height Figure Mine if new back upholstery is neededSteps 6,17 Steps 2Steps 6,11 Steps 4,8Back Angle Adjustment Figure Wheelchair to hold the insert in placeBatteries Procedure T T E R I E SGroup 24 Batteries Connecting Battery CablesProcedure 9BATTERIES TWO 2 Connector Batteryboxone 1 Connector Batterybox Battery Box BottomRemove battery terminal caps from battery Group 22 Battery Base Frames FigureBattery terminal ends Front Single BatteryBottom Tery Cable Rear Jumper Battery BoxBattery Discharge Indicator BDI When to Charge Batteries FigureBattery Discharge Indicator BDI in LCD Readout Description and Use of Battery ChargersRequired Items Recommended Battery Types INSTALLING/REMOVING Group 24 Battery Boxes FigureIf one 1 battery is defective Cleaning Battery TerminalsINSTALLING/REMOVING Group 22 Battery BOX Figure This manual REMOVING/INSTALLING the E Wiring Harness FigureProcedure Wiring Harness R N E S S Adjusting Limit Switch Figure Recline Angle 4 inches 61oReplacing Retainer Clip Retention STRAP/RETAINERReplacing Retainer Bar Perform one 1 the followingSpacer Retainer ProcedureSpacer Locknuts Mounting Screws Battery Box Sub-Frame Retainer ClipReplacing Pneumatic TIRES/ Tubes Drive WHEELS/CASTERS REMOVING/INSTALLING Drive Wheels FigureDrive Wheel Assembly Wheel Hub Four 4 Beveled Hex Nuts WHEELS/ MotorsRepeat Steps 1-4 for opposite wheel lock bracket WHEELS/MOTORSApply Loctite 242 to the two 2 mounting screws Gearbox SuspensionReplacing Forks Figure REMOVING/INSTALLING Casters FigureInstalling Casters Removing CastersLocknut Spacer Easier access to the motor/controller connectionMotor Connector Coupling Allen Washer ShockRemove motor with motor lock lever from suspen- sion arm REMOVING/INSTALLING Motor GEARLESS/BRUSHLESS Brake Release ShaftElectronics REMOVING/INSTALLING Mkiv Controller FigureRepositioning Mkiv Joystick VAN Seat Models Figure E C T R O N I C SArrow Fwd Model Recliner Positioning Limit Switch FigureSwitch Actuator Overtighten Sensor Washers C L I N E RRod Measures 3-21/32-inches Mounting Screws and Washers Replacing Recliner Cable Assemblies FigureGas Cylinder Do not Over-Tighten Gas Cylinder ActuatorREPLACING/ADJUSTING GAS Cylinders Figure Replacing Gas CylinderChanging Back Height Procedure ReclinerAdjusting Gas Cylinder Changing Seat Depth Figure Recliner ProcedureSeat Pan Removal/Replacement Procedures Changing Seat WidthRemove seat pan on recliner Plate Inside Suspension Arm AssemblyInstallbatteryboxes.Referto INSTALLING/REMOV Spacer Base Frame Seat MountBattery BOX SUB-FRAME Figure REMOVING/INSTALLING GroupBattery BOX Tray Figure MWD Wheelchairs ProcedureInstalling Group 24 Components Figure Procedure MWD WheelchairsFront Locknuts Battery Mount Frame Rear Lockn utsSteps Shock ReplacementGroup 24 Battery Base Frames Figure Install the NEW shock Shock Battery Box Sub-Frame Retainer Clip Top of ShockLarge wheel assembly Secure the top of shock between battery mountFlat Washer Shock Spring Replacement FigureBattery Mount Bracket Base Frame Mounting Screw Suspension Arm Spring WasherShock Spring Base Replacing Stabilizer Fork Assembly FigureReplacing Stabilizer Wheels Figure Replacing Stabilizer Adjusting Weight DistributionMWD Wheelchairsprocedure Cylinder Spring FigureHeight Adjustment Adjusting Stabilizers FigureAdjusting Spring Compression 16-18 x 1-1/4-inch Mounting Screws 16-18 x 2-1/2-inch REMOVING/INSTALLING Gearbox FigureReplacing Suspension ARM Figure Motor Gearbox Suspension ArmSteps 6,10 Entation. Bracket End of Suspension ArmTubular End Suspension Arm Bracket End Suspension Arm Inner Link SpacerAnti-Tipper Wheel Replacement Removing/Installing Group 22 Battery Box TrayShock Replacement Sub-FrameILocknutsBolts Rubber Procedure RWD WheelchairsBattery Tray ElementMounting Wiring Harness Shock Replacement FigureRWD Wheelchairs Procedure Screws BracketShock Mounting Screw Suspension Arm Spacer TopShock Retainer Bar Locknut Shock Mounting Screw Suspension ArmRWD Wheelchairsprocedure Group 24 Batteries only Apply LoctiteTorque and Storm X wheelchairs Rubber Element Replacement FigureShock Hex Screw Battery Mount Bracket Base Frame Mounting ScrewAdjustment Options REMOVING/INSTALLING GearboxAdjusting Weight Distribution Figure 16-18 2-inch 4-inchMounting Screws Washer Seat Support Bracket Base Frame Adjusting Weight Distribution ProcedureRepositioning the MOTOR/ Gearbox Figure Move gearbox to the position determine in StepRepositioning the GEARLESS/BRUSHLESS Motor ,14 Standard Position Lengthens the wheelSuspension Arm Mounting Washer Screws ANTI-TIPPER Wheel Replacement Figure Install the new suspension arm onto the base frameLower REMOVING/INSTALLING ANTI-TIP AssemblyAnti-Tip Washers LocknutsREMOVING/INSTALLING Side Shroud Assembly Figure REMOVING/INSTALLING Front Shroud FigureREMOVING/INSTALLING Rear Shroud Figure FWD Wheelchairs ProcedureMounting Screw Washer Side Shroud Bracket Suspension Arm REMOVING/INSTALLING Counterweight FigureProcedure FWD Wheelchairs Mounting Bracket Counterweight Bottom Shoulder Screw Replacing Group 24 Battery BOX SUB-FRAME FigureHandle Outside Lower EdgeCounterweight Bottom Shoulder Screw Bottom Slot in Mounting BracketMounting Bracket Only Screw One 1 Shown REMOVING/INSTALLING Shocks FigureBracket Mounting Screw For ClarityTIE ROD Replacement Figure Locknut Arm Small Washer Large Mounting Screw Suspension Arm Complete revolution on the TOP TWO 2 tie rodsRemove the Existing sensor cable assembly Sensor Cable Assembly Replacement FigureBattery wiring harness Detail C Socket Suspension Screw ArmSHORT Motor GearboxTie Wrap C Battery Box Sub Frame Sensor Washer Left Motor SensorReinstall the battery boxes. Refer to Installing REMOVING/INSTALLING Wiring Harness Figure Replacing the Suspension ARMTie Wrap a Procedure FWD WheelchairsTie Wrap B Adjusting Weight Distribution For New Seat Depth 14 to 16 inches Inches 17 to 18 inches 19 to 20 inchesAngle Footboard ADJUSTMENTS- DEPTH/HEIGHT/ANGLE FigureDepth HeightFootrest Angle Adjustments Horizontal Position Cam FWD Wheelchairs ProcedureRight Front Shroud Footrest105 106 Limited Warranty Limtied WarrantyOne InvacareWay ChedworthWay
Related manuals
Manual 150 pages 42.82 Kb

Arrow FWD, RWD, MWD specifications

Invacare is a renowned name in the field of mobility technologies, consistently innovating and enhancing the mobility devices market. Among its outstanding offerings are the Invacare MWD (Mid Wheel Drive), RWD (Rear Wheel Drive), and Arrow FWD (Front Wheel Drive) wheelchairs. Each of these models serves unique user needs, featuring distinct designs and functionalities.

The Invacare MWD is engineered for exceptional maneuverability. Its mid-wheel drive technology provides a centralized drive wheel, allowing for tight turns and easy navigation in confined spaces. This makes the MWD particularly suitable for indoor use, where space can be limited. The MWD also features advanced suspension systems, offering superior shock absorption. This results in a smoother ride over various terrains, enhancing user comfort and stability.

On the other hand, the Invacare RWD focuses on robust outdoor performance. With its rear-wheel drive configuration, this model has excellent traction and provides powerful acceleration. The RWD is designed for versatility, equipped with larger wheels that can handle uneven terrain while providing a stable ride. Its durable construction ensures enhanced longevity, making it an ideal choice for users who lead an active lifestyle and require reliable mobility solutions on rugged ground.

The Arrow FWD wheelchair brings another dimension with its front-wheel drive system. This design allows users to easily navigate obstacles as the front wheels can pivot over them. The Arrow FWD is particularly suited for both indoor and outdoor use, as it combines the agility of the MWD with the stability seen in the RWD. It features a compact design, making it easier for users to position themselves in various settings and social situations.

All three models utilize Invacare's cutting-edge technologies, such as advanced control systems and customizable seating options, enabling users to find their optimal comfort and support levels. The customizable features also cater to individual user needs, promoting enhanced independence.

In summary, Invacare’s MWD, RWD, and Arrow FWD wheelchairs represent an impressive blend of functionality, durability, and user-centric design. Each model presents its own unique technologies and attributes, allowing users to make informed choices based on their specific mobility requirements, lifestyle, and preferences. Whether navigating tight indoor spaces or tackling outdoor challenges, Invacare’s range of wheelchairs ensures that users can experience mobility with confidence and ease.
Top Page Image Contents