Invacare RWD, MWD, Arrow FWD Remove seat pan on recliner, Spacer Base Frame Seat Mount

Page 68

PROCEDURE 14

RECLINER

R E C L I N E R

If the seat width required is within the range of the original back canes, spreader bar and headrest pillow, the original components can still be used.

If the seat width required is NOT within the range of the origi- nal back canes, spreader bar and headrest pillow, the origi- nal components can not be used.

EQUIPMENT OPTION

INSTALLING/REPLACING ADJUSTABLE 16 TO 19-INCH DEEP RECLINER SEAT FRAME ONTO ARROW OR X BASE FRAME (FIGURE 7)

1.PerforminstructionsoutlinedinPREPARATIONSFOR REMOVING/INSTALLINGSEATFRAME(STANDARD FRAME,ADJUSTABLEFRAME,ANDCAPTAINSVAN SEAT) in PROCEDURE 6 of this manual:

2.Perform one (1) of the following in PROCEDURE 7 of this manual:

A.Remove standard seat frame subassembly. Refer to REMOVING/INSTALLING STANDARD SEAT FRAMESUBASSEMBLY.

B.Remove adjustable seat frame subassembly. Re- fer to INSTALLING/REMOVING ADJUSTABLE SEAT FRAME ASSEMBLY AND OR COMPO- NENTREPLACEMENT.

C.Remove captains van seat. Refer to INSTALLING/ REMOVINGCAPTAINSVANSEATASSEMBLY.

3.Remove seat pan on recliner.

4.Installnewreclinerseatassemblyontoseatmountplates.

5.Securereclinerseatassemblytoseatmountplateswith the mounting screws, spacers and locknuts. Torque the mounting screws to 156-inch pounds.

NOTE: There are three (3) types of seat mount plates; low, medium, and high heights. The seat mount plate shown in this illustration represents the medium height. Refer to

MOUNTINGPLATE-SEATANGLEADJUSTMENTAND INSTALLATION ORIENTATION in PROCEDURE 6 of this manual for illustrations of the low and high heights.

6.Positionlimitswitchontowheelchair.RefertoPOSITION- INGLIMITSWITCHinthisprocedureofthemanual.

7.Reinstall recliner seat pan with existing six (6) mount- ing screws.

8.Install the two (2) warnings labels onto the two (2) suspension arm assemblies. Refer to FIGURE 7 for correct label placement.

9.Installbatterybox(es).Referto INSTALLING/REMOV-

ING BATTERY BOXES- GROUP 24 BATTERY BASE FRAMES or INSTALLING/REMOVING BAT-

TERY BOX - GROUP 22 BATTERY BASE FRAMES in PROCEDURE 9 of this manual.

10.Perform instructions outlined in PREPARATIONS FOR REMOVING/INSTALLING SEAT FRAME (STANDARD FRAME, ADJUSTABLE FRAME, AND CAPTAINS VAN SEAT) in PROCEDURE 6 of this manual:

Recliner

Mounting

Seat Assembly

Screws

 

Spacer

Base

Frame

Seat Mount

Locknuts

Plate

 

 

Warning Label

Inside of

Suspension Arm

Assembly

FIGURE 7 - INSTALLING/REPLACING ADJUSTABLE 16 TO 19-INCH DEEP RECLINER SEAT FRAME ONTO ARROW OR X BASE

68

Page 67 Page 69
Image 68
Page 67 Page 69
Contents Storm Series Wheelchairs R N I N G E C I a L T E STable of Contents Table of Contents Limited Warranty Specification S SpecificationsSpecifications Arrow FWD has a 400 lb. ratingProcedure General Guidelines Repair or Service InformationGeneral Guidelines Procedure MOTOR/GEARBOXMWD Models FWD ModelsSuspension Arm Located on insideUsing Hydrometer to Check Battery Cells Lead Acid Figure Troubleshooting ProcedureBattery Charger Field Load Test FigureMotor Testing Figure Procedure TroubleshootingNumber of Floating Balls Will Vary According to ChargeELECTRO-MECHANICAL Parking Brake Testing Figure Ohmmeter Motor ConnectorCap Motor Pin Motor Connector Cap Motor Pin Motor Connector OhmmeterHardware Torque Specifications Standard Seat FrameAdjustable Seat Frame Hardware Torque Specifications ProcedureCaptains VAN Seat Loctite and Torque to 75 in/lbs Torque to 156 in/lbsInch Wheels Wheel HalvesPneumatic with Flat-Free Wheel Halves Torque to Pneumatic Wheel Halves 8 inch Torque to 18 in/lbsInch Wheels Wheel Halves Pneumatic with Flat-FreeTorque to 156 in/lbs 1020 in/lbs Wheel Halves Torque to In/lbsTorque to 156 in/lbs Torque to 160 in/lbs Loctite Torque to 360 in/lbs Torque to 156 in/lbsArms Procedure This Procedure Includes the FollowingReplacing Armrest Pads Captains VAN Seats Figure Replacing Captains VAN Seat Armrest Plate FigureReplacing Seat Positioning Y Strap Captains VAN Seats Replacing Back Upholstery FigureH O L S T E R Y M E REMOVING/INSTALLING Standard Seat Frame Subassembly Figure Seat Frame ProcedureReplacing Exact Same Size Standard Seat Frame Mounting ScrewsAdjustable Seat Frame Figure Seat FrameInches Inch Inch deep InchesChanging Seat Depth Between 12 and 15- Inches Figure A T M ETorque to Standard Seat Frame Changing Seat Width Standard and Adjustable Seat FrameMounting Screws Torque to 75-inch pounds Seat Width Side Spacers CenterComponent Replacement PoundsCoved Washer Center FrameINSTALLING/REMOVING Captains VAN Seat Assembly Figure Installing Captains Van SeatRemoving Captains Van Seat Torque to Inch poundsAdjustable Frames Captains Van SeatREMOVING/INSTALLING Seat PAN Figure InstallingRemove the seat cushion from the seat pan Locknut Quick Release PinSeat Dump Seat Angle AdjustmentInstallation Orientation Base Frame Procedure Replacing Seat Mounting Plates FigureReplacing Seat Support Brackets Figure S E M EProcedure Base Frame Replacing Seat Support Bracket T-NUTS FigureMounting Screws Washer Seat Support Bracket BaseT-Nut Frame Channel Cover Seat Support Mounting ScrewReplacing Battery Charger Bracket and T-NUT Battery Charg er Charger Connector MountRWD and MWD Models Figure Arrow FWD Model FigureREMOVING/INSTALLING Seat Stop Screws Figure Mounting Screw Battery Charger ConnectorReplace the battery charger mount bracket and se Tightensecurely Reverse A, 3B or 3CREMOVING/INSTALLING CJ Back Brackets Figure Back Frame ProcedureC K M E CJ Bracket MountsProcedure Back Frame Changing Back Height FigureHeavy Duty Models Mine if new back upholstery is neededSteps 2 Steps 6,11Steps 6,17 Steps 4,8Back Angle Adjustment Figure Wheelchair to hold the insert in placeBatteries Procedure T T E R I E SGroup 24 Batteries Connecting Battery CablesProcedure 9BATTERIES TWO 2 Connector Batteryboxone 1 Connector Batterybox Battery Box BottomRemove battery terminal caps from battery Group 22 Battery Base Frames FigureBattery terminal ends Single Battery Bottom Tery Cable Rear Jumper BatteryFront BoxWhen to Charge Batteries Figure Battery Discharge Indicator BDI in LCD ReadoutBattery Discharge Indicator BDI Description and Use of Battery ChargersRequired Items INSTALLING/REMOVING Group 24 Battery Boxes Figure If one 1 battery is defectiveRecommended Battery Types Cleaning Battery TerminalsINSTALLING/REMOVING Group 22 Battery BOX Figure This manual REMOVING/INSTALLING the E Wiring Harness FigureProcedure Wiring Harness R N E S S Adjusting Limit Switch Figure Recline Angle 4 inches 61oRetention STRAP/RETAINER Replacing Retainer BarReplacing Retainer Clip Perform one 1 the followingProcedure Spacer Locknuts Mounting Screws Battery Box Sub-FrameSpacer Retainer Retainer ClipREMOVING/INSTALLING Drive Wheels Figure Drive Wheel Assembly Wheel Hub Four 4 Beveled Hex NutsReplacing Pneumatic TIRES/ Tubes Drive WHEELS/CASTERS WHEELS/ MotorsWHEELS/MOTORS Apply Loctite 242 to the two 2 mounting screwsRepeat Steps 1-4 for opposite wheel lock bracket Gearbox SuspensionREMOVING/INSTALLING Casters Figure Installing CastersReplacing Forks Figure Removing CastersEasier access to the motor/controller connection Motor Connector Coupling AllenLocknut Spacer Washer ShockRemove motor with motor lock lever from suspen- sion arm REMOVING/INSTALLING Motor GEARLESS/BRUSHLESS Brake Release ShaftREMOVING/INSTALLING Mkiv Controller Figure Repositioning Mkiv Joystick VAN Seat Models FigureElectronics E C T R O N I C SArrow Fwd Model Positioning Limit Switch Figure Switch Actuator Overtighten Sensor WashersRecliner C L I N E RReplacing Recliner Cable Assemblies Figure Gas CylinderRod Measures 3-21/32-inches Mounting Screws and Washers Do not Over-Tighten Gas Cylinder ActuatorREPLACING/ADJUSTING GAS Cylinders Figure Replacing Gas CylinderChanging Back Height Procedure ReclinerAdjusting Gas Cylinder Recliner Procedure Seat Pan Removal/Replacement ProceduresChanging Seat Depth Figure Changing Seat WidthPlate Inside Suspension Arm Assembly Installbatteryboxes.Referto INSTALLING/REMOVRemove seat pan on recliner Spacer Base Frame Seat MountREMOVING/INSTALLING Group Battery BOX Tray FigureBattery BOX SUB-FRAME Figure MWD Wheelchairs ProcedureProcedure MWD Wheelchairs Front Locknuts Battery MountInstalling Group 24 Components Figure Frame Rear Lockn utsSteps Shock ReplacementGroup 24 Battery Base Frames Figure Shock Battery Box Sub-Frame Retainer Clip Top of Shock Large wheel assemblyInstall the NEW shock Secure the top of shock between battery mountShock Spring Replacement Figure Battery Mount Bracket Base FrameFlat Washer Mounting Screw Suspension Arm Spring WasherShock Spring Base Replacing Stabilizer Fork Assembly FigureReplacing Stabilizer Wheels Figure Adjusting Weight Distribution MWD WheelchairsprocedureReplacing Stabilizer Cylinder Spring FigureHeight Adjustment Adjusting Stabilizers FigureAdjusting Spring Compression REMOVING/INSTALLING Gearbox Figure Replacing Suspension ARM Figure16-18 x 1-1/4-inch Mounting Screws 16-18 x 2-1/2-inch Motor Gearbox Suspension ArmEntation. Bracket End of Suspension Arm Tubular End Suspension ArmSteps 6,10 Bracket End Suspension Arm Inner Link SpacerRemoving/Installing Group 22 Battery Box Tray Shock ReplacementAnti-Tipper Wheel Replacement Sub-FrameProcedure RWD Wheelchairs Battery TrayILocknutsBolts Rubber ElementShock Replacement Figure RWD Wheelchairs ProcedureMounting Wiring Harness Screws BracketSpacer Top Shock Retainer BarShock Mounting Screw Suspension Arm Locknut Shock Mounting Screw Suspension ArmRWD Wheelchairsprocedure Group 24 Batteries only Apply LoctiteRubber Element Replacement Figure Shock Hex Screw Battery Mount BracketTorque and Storm X wheelchairs Base Frame Mounting ScrewREMOVING/INSTALLING Gearbox Adjusting Weight Distribution FigureAdjustment Options 16-18 2-inch 4-inchAdjusting Weight Distribution Procedure Repositioning the MOTOR/ Gearbox FigureMounting Screws Washer Seat Support Bracket Base Frame Move gearbox to the position determine in StepRepositioning the GEARLESS/BRUSHLESS Motor ,14 Standard Position Lengthens the wheelSuspension Arm Mounting Washer Screws ANTI-TIPPER Wheel Replacement Figure Install the new suspension arm onto the base frameREMOVING/INSTALLING ANTI-TIP Assembly Anti-TipLower Washers LocknutsREMOVING/INSTALLING Front Shroud Figure REMOVING/INSTALLING Rear Shroud FigureREMOVING/INSTALLING Side Shroud Assembly Figure FWD Wheelchairs ProcedureMounting Screw Washer Side Shroud Bracket Suspension Arm REMOVING/INSTALLING Counterweight FigureProcedure FWD Wheelchairs Replacing Group 24 Battery BOX SUB-FRAME Figure Handle Outside Lower EdgeCounterweightMounting Bracket Counterweight Bottom Shoulder Screw Bottom Shoulder Screw Bottom Slot in Mounting BracketREMOVING/INSTALLING Shocks Figure Bracket Mounting ScrewMounting Bracket Only Screw One 1 Shown For ClarityTIE ROD Replacement Figure Locknut Arm Small Washer Large Mounting Screw Suspension Arm Complete revolution on the TOP TWO 2 tie rodsSensor Cable Assembly Replacement Figure Battery wiring harness Detail CRemove the Existing sensor cable assembly Socket Suspension Screw ArmSHORT Motor GearboxTie Wrap C Battery Box Sub Frame Sensor Washer Left Motor SensorReinstall the battery boxes. Refer to Installing REMOVING/INSTALLING Wiring Harness Figure Replacing the Suspension ARMTie Wrap a Procedure FWD WheelchairsTie Wrap B Adjusting Weight Distribution For New Seat Depth 14 to 16 inches Inches 17 to 18 inches 19 to 20 inchesFootboard ADJUSTMENTS- DEPTH/HEIGHT/ANGLE Figure DepthAngle HeightFootrest Angle Adjustments FWD Wheelchairs Procedure RightHorizontal Position Cam Front Shroud Footrest105 106 Limited Warranty Limtied WarrantyOne InvacareWay ChedworthWay
Related manuals
Manual 150 pages 42.82 Kb

Arrow FWD, RWD, MWD specifications

Invacare is a renowned name in the field of mobility technologies, consistently innovating and enhancing the mobility devices market. Among its outstanding offerings are the Invacare MWD (Mid Wheel Drive), RWD (Rear Wheel Drive), and Arrow FWD (Front Wheel Drive) wheelchairs. Each of these models serves unique user needs, featuring distinct designs and functionalities.

The Invacare MWD is engineered for exceptional maneuverability. Its mid-wheel drive technology provides a centralized drive wheel, allowing for tight turns and easy navigation in confined spaces. This makes the MWD particularly suitable for indoor use, where space can be limited. The MWD also features advanced suspension systems, offering superior shock absorption. This results in a smoother ride over various terrains, enhancing user comfort and stability.

On the other hand, the Invacare RWD focuses on robust outdoor performance. With its rear-wheel drive configuration, this model has excellent traction and provides powerful acceleration. The RWD is designed for versatility, equipped with larger wheels that can handle uneven terrain while providing a stable ride. Its durable construction ensures enhanced longevity, making it an ideal choice for users who lead an active lifestyle and require reliable mobility solutions on rugged ground.

The Arrow FWD wheelchair brings another dimension with its front-wheel drive system. This design allows users to easily navigate obstacles as the front wheels can pivot over them. The Arrow FWD is particularly suited for both indoor and outdoor use, as it combines the agility of the MWD with the stability seen in the RWD. It features a compact design, making it easier for users to position themselves in various settings and social situations.

All three models utilize Invacare's cutting-edge technologies, such as advanced control systems and customizable seating options, enabling users to find their optimal comfort and support levels. The customizable features also cater to individual user needs, promoting enhanced independence.

In summary, Invacare’s MWD, RWD, and Arrow FWD wheelchairs represent an impressive blend of functionality, durability, and user-centric design. Each model presents its own unique technologies and attributes, allowing users to make informed choices based on their specific mobility requirements, lifestyle, and preferences. Whether navigating tight indoor spaces or tackling outdoor challenges, Invacare’s range of wheelchairs ensures that users can experience mobility with confidence and ease.
Top Page Image Contents