Adjusting the Growth Bracket Figure | Invacare KSS specification

NOTE: On the back, the standard attachment points are the top and bottom sets of holes. Refer to the ATTACH- MENT POINTS chart in this instruction sheet for optional attachment points.

4.Install four (4) of the mounting screws through the holes in the growth bracket and into the underside of the Ulti-Mate Base. Securely tighten.

NOTE: On the seat, the standard attachment points are the front and back sets of holes. Refer to the ATTACH- MENT POINTS chart in this instruction sheet for optional attachment points.

5.If adjustment is required, refer to ADJUSTING THE GROWTH BRACKET in this instruction sheet. Oth- erwise, continue on with ATTACHING/ADJUSTING THE LATERAL SUPPORTS in this instruction sheet.

Curved
Back
		Center Panel
	Top Set	Six (6) T-nutted
		Six (6) T-nutted
		Mounting Holes
	Bottom Set	Mounting Holes
	Bottom Set
		Mounting
		Mounting
Ulti-Mate		Screws
Ulti-Mate
Base

Adjustment	Growth Bracket
Holes

NOTE: Your Growth Bracket may have SLOTS in- stead of Adjustment Holes.

FIGURE 1 - ATACHING/ADJUSTING THE FIXED

G RO WTH BRACKET-CHILD/JUNIOR SIZES

Adjusting the Growth Bracket (FIGURE 1)

NOTE:The growth bracket provides up to a 3-inch depth adjustment and up to a 3-inch height adjustment.

ADJUSTING THE BACK HEIGHT.

1.If necessary, unzip center panel of the back cover.

2.Remove the four (4) mounting screws that secure the growth bracket to the back.

3.Adjust the back up or down until the desired mount- ing position is obtained.

4.Reinstall the four (4) mounting screws through the growth bracket and into the back shell. Securely tighten. Refer to the ATTACHMENT POINTS chart in this instruction sheet for standard and optional attachment points.

5.If all attachments and adjustments are complete, zip center panel of back cover closed.

ADJUSTING THE ULTI-MATE BASE DEPTH.

1.Remove the four (4) mounting screws that secure the growth bracket to the Ulti-Mate Base.

2.Adjust the seat forward or back until the desired mounting position is obtained.

3.Reinstall the four (4) mounting screws through the growth bracket and into the seat. Securely tighten. Refer to the ATTACHMENT POINTS chart in this instruction sheet for standard and optional attach- ment points.

ATTACHING / ADJUSTING THE ADJUSTABLE ANGLE GROWTH BRACKET (FIGURE 2)

ATTACHING THE ADJUSTABLE ANGLE GROWTH BRACKET

NOTE: The growth bracket attaches to the child/junior sized curved back ONLY.

1.Remove the adjustable angle growth bracket and attaching hardware from the packaging.

2.Unzip the center panel of the back cover, exposing the six (6) T-nutted mounting holes.

NOTE: Make sure that the growth bracket is positioned correctly. The flat portion of the adjustable angle bracket growth bracket provides depth adjustment for the Ulti- mate base. The angled portion of the adjustable angle bracket height adjustment for the curved back (FIGURE 1).

3.Install four (4) of the mounting screws through the slots in the adjustable angle growth bracket and into the underside of the Ulti-mate base. Securely tighten.

NOTE: On the Ulti-mate base, the standard attachment points are the front and rear four (4) holes. Refer to the ATTACHMENT POINTS in this instruction sheet for optional attachment points.

4.Install two (2) of the mounting screws through the slots on the adjustable angle growth bracket and into the back shell. Securely tighten.

NOTE: On the curved back, the standard attachment points are the MIDDLE set of holes. Refer to the ATTACHMENT POINTS in this instruction sheet for optional attachment points.

5.If adjustment is required, refer to ADJUSTING THE GROWTH BRACKET in this instruction sheet.

ADJUSTING THE GROWTH BRACKET

ADJUSTING THE BACK HEIGHT.

1. If necessary, unzip center panel of the back cover.