E&J GF0600050REVE06 manual Troubleshooting battery charger

Page 43

 

Troubleshooting: battery charger

 

SYMPTOM

CHECK—ACTION

 

Green status LED OFF;

Check that the battery charger is connected and switched ON.

AC voltage

Battery capacity level

 

 

switch

indicator LED ON

Check that the battery charger is plugged into a working power outlet.

 

 

Battery voltage switch on wrong setting—check and ensure that for

 

 

U.S. and Canada, switch is set to 115V. If not, use a small screwdriver

back

 

to change to correct setting, as shown in picture at right.

 

 

panel

Check / replace the AC fuse as shown below.

WARNING: Before checking the AC fuse, disconnect the battery charger from both

power outlet and wheelchair battery charger receptacle

1.Hold line connector by its body and pull straight out from battery

charger as shown in picture at right.

2. Use a small screwdriver to open AC fuse compartment cover as

back

shown in lower picture at right.

 

panel

3.Slide AC fuse compartment out from battery charger. There is a spare fuse in the compartment.

line connector

4.Replace AC fuse with spare. If spare fuse has been used, replace with same size and type.

5.Replace cover.

WARNING: Do NOT replace the AC fuse with the output fuse. They have different fuse ratings, and interchanging them could result in fire.

AC fuse compartment

Battery charger is damaged. Contact your dealer.

Green status LED always on (nonflashing); Battery capacity level indicator LEDs all OFF; batteries won't charge

Note: The charge indicator LED will be nonflashing green when the battery charger power is switched on, but should change to flashing battery status pattern when the batteries are charging.

Batteries not connected—connect batteries.

Battery terminals not connected—connect battery terminals.

Batteries not connected properly, or polarity reversed—correct connections.

Batteries severely discharged, below 1/2 volt—replace batteries.

Batteries defective—replace batteries.

Output fuse blown—check / replace the output fuse.

WARNING: Before checking the output fuse, disconnect battery charger from both power outlet and wheelchair battery charger receptacle.

To check the output fuse:

 

1.

Unscrew fuse, shown in picture at right, in direction of arrow.

 

2.

Replace with same size and type.

front output fuse

WARNING: Do NOT replace the output fuse with the AC fuse. They

panel

 

have different fuse ratings, and interchanging them could result in fire.

Contact your Graham-Field Health Products dealer.

Everest with Captain Seat Owner's Manual

GF0600050RevE06, August 2006

43

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Everest Contents Introduction II Important safety precautions GF0600050RevE06, August GF0600050RevE06, August Electromagnetic interference EMI from radio wave sources Powered Wheelchair Electromagnetic Interference EMIImportant Information EMI WarningsReaching / bending III Handling tipsBalance Transfer activitiesDescent BackwardRamps and Inclines AscentIV Getting started Power drive systemController cable JoystickSpeed / profile decrease button Battery indicatorMaximum speed / profile indicator Horn buttonOperating instructions Adjust hand control extension Backward / forward VI AdjustmentsAdjust hand control extension-change sides Adjust arm space from seat frame width between arms Back Fold back down Adjust back angleHeadrest Adjust headrest heightSeat Install seat refer to the pictures at rightRemove seat refer to the pictures at right Adjust seat height refer to the pictures on previous Cowl Remove cowl refer to the picture at right Install cowl refer to the picture aboveAdjust individual footplate extension length Adjust footplate extension length see picture at rightVII Batteries Guidelines to extending battery lifeBattery capacity level indicator Battery chargerBattery charger front panel Output cable and connector Status indicatorSafety-charging the batteries Charging the batteries Remove and install batteries Install batteries Adjust battery brackets if necessaryGF0600050RevE06, August Clean battery terminals Regular battery maintenance Clean batteriesDo-it-yourself maintenance Viii MaintenanceCheck joystick List of tools and suppliesGeneral care Charge batteriesControl system cable connections Front wheel drive Control system cable connections Rear wheel drive Check controller & park brakes Clean frameCheck & clean upholstery Check tiresInspect motor brushes Check caster forksCheck bearings IX Troubleshooting Batteries General TroubleshootingGeneral diagnostic guide Troubleshooting controllerWheelchair will be operable when the following faults occur Battery indicator control system status displayBattery indicator control system fault display Power outlet and wheelchair battery charger receptacle Troubleshooting battery chargerGF0600050RevE06, August Warranty Periods Limited WarrantyGF0600050RevE06, August XI Index

GF0600050REVE06 specifications

E&J GF0600050REVE06 is a high-performance product known for its innovative features and advanced technologies. Designed to cater to the needs of both commercial and residential applications, this model has gained recognition for its reliability and efficiency in various environments.

One of the standout features of the E&J GF0600050REVE06 is its robust construction. Built with high-quality materials, it ensures durability and longevity in operations, making it a smart investment for users seeking long-term performance. The design is not only functional but also aesthetically pleasing, allowing it to blend seamlessly into different settings.

The E&J GF0600050REVE06 boasts significant energy efficiency, which is becoming increasingly important in today's eco-conscious market. With its state-of-the-art energy conversion technologies, it minimizes waste and enhances overall energy usage, providing significant savings on operational costs over time. Users can expect lower utility bills without compromising on performance, a crucial consideration for budget-conscious individuals and businesses alike.

Another noteworthy characteristic of this product is its user-friendly interface. Equipped with advanced control systems, it allows for easy monitoring and adjustment, catering to the varying needs of its users. Whether it's adjusting settings for optimal performance or accessing diagnostic features, the intuitive layout ensures that even those with minimal technical knowledge can operate the device effortlessly.

Moreover, the E&J GF0600050REVE06 incorporates several safety features, ensuring peace of mind during operation. These include automatic shut-off systems and temperature regulation, which protect the unit and the surrounding environment from potential hazards. This focus on safety not only enhances user confidence but also promotes a safer working environment.

Additionally, the technology behind the E&J GF0600050REVE06 supports seamless integration with other smart devices. This capability allows users to control and monitor the device remotely, facilitating greater flexibility and convenience in management.

In conclusion, the E&J GF0600050REVE06 stands out as a leading choice for those seeking advanced technology, energy efficiency, and a commitment to safety and durability. Its thoughtful design and innovative features make it an essential tool for modern users, enhancing productivity and operational effectiveness. With its excellent performance and user-centric approach, the E&J GF0600050REVE06 really sets itself apart in a competitive market.
Top Page Image Contents