Omega CL3512A specifications 3806/0610

Page 10

WARRANTY / DISCLAIMER

OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of 13 months from date of purchase. OMEGA Warranty adds an additional one (1) month grace period to the normal one (1) year product warranty to cover handling and shipping time. This ensures that OMEGA's customers receive maximum coverage on each product. If the unit should malfunction, it must be returned to the factory for evaluation. OMEGA's Customer Service Department will issue an Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA, if the unit is found to be defective it will be repaired or replaced at no charge. OMEGA's WARRANTY does not apply to defects resulting from any action of the purchaser, including but not limited to mishandling, improper interfacing, operation outside of design limits, improper repair, or unauthorized modification. This WARRANTY is VOID if the unit shows evidence of having been tampered with or shows evidence of being damaged as a result of excessive corrosion; or current, heat moisture or vibration; improper specification; misapplication; misuse or other operating conditions outside of OMEGA's control. Components which wear are not warranted, including but not limited to contact points, fuses, and triacs.

OMEGA is pleased to offer suggestions on the use of its various products. However, OMEGA neither assumes responsibility for any omissions or errors nor assumes liability for any damages that result from the use of its products in accordance with information provided by OMEGA, either verbal or written. OMEGA warrants only that the parts manufactured by it will be as specified and free of defects. OMEGA MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF TITLE AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION OF LIABILITY: The remedies of purchaser set forth herein are exclusive and the total liability of OMEGA with respect to this order, whether based on contract, warranty, negligence, indemnification, strict liability or otherwise, shall not exceed the purchase price of the component upon which liability is based. In no event shall OMEGA be liable for consequential, incidental or special damages.

CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a "Basic Component" under 10 CFR 21 (NRC), used in or with any nuclear installation or activity; or (2) in medical applications or used on humans. Should any Product(s) be used in or with any nuclear installation or activity, medical application, used on humans, or misused in any way, OMEGA assumes no responsibility as set forth in our basic WARRANTY / DISCLAIMER language, and additionally, purchaser will indemnify OMEGA and hold OMEGA harmless from any liability or damage whatsoever arising out of the use of the Product(s) in such a manner.

RETURN REQUESTS / INQUIRIES

Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department. BEFORE RETURNING ANY PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER FROM OMEGA'S CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING DELAYS). The assigned AR number should then be marked on the outside of the return package and on any correspondence.

The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent breakage in transit.

FOR WARRANTY RETURNS, please have the following information available BEFORE contacting OMEGA:

1.P.O. number under which the product was PURCHASED.

2.Model and serial number of the product under warranty, and

3.Repair instructions and/or specific problems relative to the product.

FOR NON-WARRANTY REPAIRS, consult OMEGA for current repair charges. Have the following information available BEFORE contacting OMEGA:

1.P.O. number to cover the COST of the repair.

2.Model and serial number of product , and

3.Repair instructions and/or specific problems relative to the product.

OMEGA's policy is to make running changes, not model changes, whenever an improvement is possible. This affords our customers the latest in technology and engineering. OMEGA is a registered trademark of OMEGA ENGINEERING, INC. © Copyright 2002 OMEGA ENGINEERING, INC. All rights reserved. This document may not be copied, photocopied, reproduced, translated, or reduced to any electronic medium or machine-readable from, in whole or in part, without prior written consent of OMEGA ENGINEERING, INC.

Where Do I Find Everything I Need for

Process Measurement and Control?

OMEGA…Of Course!

TEMPERATURE

DATA ACQUISITION

￿ Thermocouple, RTD & Thermistor

￿ Data Acquisition & Engineering Software

Probes, Connectors, Panels & Assemblies

￿ Communications-Based

￿ Wire: Thermocouple, RTD & Thermistor

Acquisition Systems

￿ Calibrators & Ice Point References

￿ Plug-in Cards for Apple, IBM &

￿ Recorders, Controllers & Process Monitors

Compatibles

￿ Infrared Pyrometers

￿ Datalogging Systems

PRESSURE/STRAIN AND FORCE

￿ Recorders, Printers & Plotters

 

￿ Transducers & Strain Gauges

HEATERS

￿ Load Cells & Pressure Gauges

￿ Heating Cable

￿ Displacement Transducers

￿ Cartridge & Strip Heaters

￿ Instrumentation & Accessories

￿ Immersion & Band Heaters

FLOW/LEVEL

￿ Flexible Heaters

￿ Laboratory Heaters

￿ Rotameters, Gas Mass Flowmeters &

 

Flow Computers

ENVIRONMENTAL

￿ Air Velocity Indicators

MONITORING AND CONTROL

￿ Turbine/Paddlewheel Systems

￿ Metering & Control Instrumentation

￿ Totalizers & Batch Controllers

￿ Refractometers

pH/CONDUCTIVITY

￿ Pumps & Tubing

￿ Air, Soil & Water Monitors

￿ pH Electrodes, Testers & Accessories

￿ Industrial Water & Wastewater Treatment

￿ Benchtop/Laboratory Meters

￿ pH, Conductivity & Dissolved Oxygen

￿ Controllers, Calibrators, Simulators

Instruments

& Pumps

 

￿ Industrial pH & Conductivity Equipment

 

M-3806/0610

 

Image 10
Contents CL3512A Table of contents Introduction Safety InformationUnpacking Descriptions of Buttons and Switches Operation ProcedureDrawing of Unit Adjust Read Mode ProcedureSelector Switch Input SelectionsSource Mode Procedure Calibration Simulation Battery Replacement Operator MaintenanceSpecifications Measurement Range ThermocoupleCL3152A Calibration Procedure Measurement rate 1 times/secondPage 3806/0610