Sterling 822.00292.00 specifications Appendix, Technical Specifications, Annex B Information

Page 53

Chapter 8: Appendix

8-1 Technical Specifications

Annex B Information

The following design information is provided for your reference:

1.

No modifications are allowed to this equipment that could alter the CE compliance

2.

Ambient temperature:

0 degrees Celsius – Maximum (104 degrees Fahrenheit)

3.

Humidity range:

50% relative humidity

 

4.

Altitude:

Sea level

 

 

5.

Environment:

Clean, dust-free and non-explosive

6.

Radiation:

None

 

 

7.

Vibration:

Minimal, i.e. machine mounting

 

8.

Allowable voltage fluctuation:

+/- 10%

 

9.

Allowable frequency fluctuation:

Continuous

+/- 1%

 

 

 

Intermittent

+/- 2%

10.

Nominal supply voltage:

460/3/60 (Verify on serial number tag)

11.Earth ground type: TN (system has one point directly earthed through a protective conductor)

12.Power supply should include a ground connection.

13.Over-current protection is supplied in the dryer, but additional protection should be supplied by the user.

14.The door-mounted disconnect serves as the electrical disconnect device.

15.Dryer is not equipped with local lighting.

16.Functional identification

17.Dryer is equipped with a CE mark

18.Dryer is supplied with an operating manual in the language of the destination country.

19.Cable support may be required for power cord, depending on final installation.

20.No one is required to be in the interior of the electrical enclosure during the normal operation of the unit. Only skilled electricians should be inside the enclosure for maintenance.

21.Doors can be opened with a screwdriver, but no keys are required.

22.Two-hand control is not required or provided.

23.All dryers should be moved around and set in a place with a lift truck or equivalent.

24.There are no frequent repetitive cycles that require manual control⎯repetitive functions are automatic while the dryer is operating.

25.An inspection report detailing the functional test is included with the dryer.

26.The machine is not equipped with cableless controls.

27.Color-coded (harmonized) power cord is sufficient for proper installation.

Aftercooler Design Specifications

 

Entering water temp.

ºF

 

ºC

85ºF

 

29ºC

Large Dehumidifying Dryers

Appendix

53

Page 52 Page 54
Image 53
Page 52 Page 54
Contents SDA 1000-5100 Large Dehumidifying Dryers With AP0 Controls Unpacking and Inspection Shipping InfoEvent of Shipping Damage If the Shipment is Not CompleteCredit Returns Warranty ReturnsReturns Table of Contents Operation Dryer Identification Serial Number Tag Technical Assistance Safety Symbols Used in this Manual SafetyHow to Use This Manual Wear Safety Glasses and Work Gloves Dryer Safety Tags DescriptionOperator Responsibility ResponsibilityGeneral Responsibility Maintenance Responsibility Reporting a Safety Defect General Description Functional DescriptionModels Covered in This Manual Regeneration Cycle Process/Regeneration CycleSequence of Operation Controller Screen Descriptions Controller DescriptionElectrical Features Standard FeaturesMechanical Features Process Aftercooler OptionsClosed-Loop Regeneration Material Overdrying Protection Recommended Temperature SettingsProcess Air Dust Collector Electrical Options Mechanical OptionsSafety Circuit Standards Safety Devices and InterlocksSafety Device Lock-Outs Fail Safe OperationPage Uncrating the Equipment Mechanical InstallationRigging and Placing Unit Making Electrical ConnectionsChecking Blower Rotation Checking for Proper Blower RotationDryer/Drying Hopper Process Air Connections Making Dryer/Drying Hopper Process Air ConnectionsAftercooler Components & Flow Rates Connecting Aftercooler/Precooler Cooling Water OptionalDrying Hopper Air Trap Using the Drying Hopper Air TrapIndicator Lights SwitchesProcess Air Temperature Controller ControlsLit when Control Output 2 is on. Not used Lit when Control Output 1 is on. The Out1Indicator Name Description Lights in the Operation Indicator Section whenE5CN Operating Parameters Setting the Process Air TemperatureTuned prior to dryer startup Adjustment Level Indicator Name DescriptionON, OFF Entering Operating Parameters to Select ModesOptional Setting the High Dew Point AlarmProcess Air Dew Point Display Watlow Operating Parameters Redundant Safety Controller DisplaySetting the Redundant Safety Controller Manf. setting Operation Auto-Tuning the DryerInitial Start-up Pre-Startup ChecksDryer Operation Procedures Page Material Miser OFF Press + to Enable Alarm Display Messages Shutting Down the Dryer Auto-Tuning the DryerPhotocopy this page for your maintenance records MaintenanceMaintenance Schedule Cleaning or Replacing the Process Air Filters Preventative MaintenanceCalibrating the Dirty Filter Alarm Cleaning or Replacing the Regeneration FilterChecking the Dewpoint Control System Replacing the Desiccant Corrective MaintenanceSymptoms of Worn Out Desiccant Replacing the Process Heater Electric Dryers Desiccant Tower AssemblyReplacing the Regeneration Heater Electric Dryers Process Heater Box AssemblyRegeneration Heater Box Assembly Introduction TroubleshootingBasic Troubleshooting Large Dehumidifying Dryers Troubleshooting Alarm Alarm Description Alarm Effect Code AlarmsAlarm Descriptions Using a Platinum Resistance Thermometer Determining Temperature Controller Errors or Sensor ErrorsUsing a Thermocouple Aftercooler Design Specifications Technical SpecificationsAppendix Annex B InformationDrawings and Diagrams Optional dryer dust collector Spare Parts List Level 3 Mechanical Components Located on back of Dryer Dryer Identification Serial Number TagTechnical Assistance Service DepartmentParts Department Sales Department

822.00292.00 specifications

Sterling 822.00292.00 is an advanced piece of equipment that stands out in the competitive landscape of modern machinery. Known for its precision engineering and robust performance, this model is particularly favored in industries requiring reliability and efficiency.

One of the main features of the Sterling 822.00292.00 is its high-performance motor, designed to deliver exceptional power while maintaining energy efficiency. This motor is bolstered by advanced cooling technologies that ensure optimal performance during prolonged use. As a result, users can expect minimal downtime and reduced wear and tear, enhancing the lifespan of the equipment.

The device also incorporates cutting-edge digital control systems, which facilitate easy operation and monitoring. This technology allows operators to make real-time adjustments, improving overall workflow and productivity. The user interface is designed with simplicity in mind, making it accessible for both seasoned professionals and newcomers alike.

In terms of construction, the Sterling 822.00292.00 is built with durable materials that withstand harsh working conditions. Its robust frame ensures stability, while the compact design allows for easy integration into various environments, from industrial plants to smaller workshops.

Another noteworthy characteristic of the Sterling 822.00292.00 is its versatility. The machine is designed to handle a wide range of applications, making it suitable for diverse sectors, including manufacturing, automotive, and aerospace. This adaptability is further enhanced by interchangeable components, which allow for customization based on specific operational needs.

Safety is paramount in the design of the Sterling 822.00292.00. The equipment is equipped with multiple safety features, including emergency shut-off systems and protective enclosures. These elements not only safeguard the operators but also contribute to the overall integrity of the machinery, reducing the risk of accidents and ensuring compliance with industry standards.

Furthermore, the Sterling 822.00292.00 is backed by extensive customer support and a comprehensive warranty, highlighting the manufacturer's commitment to quality and customer satisfaction. Users can access a wealth of resources, including manuals and troubleshooting guides, ensuring they can maximize the potential of their investment.

In conclusion, the Sterling 822.00292.00 represents a blend of innovation, reliability, and user-friendliness. With its impressive array of features and technologies, it has become a go-to option for professionals across various industries looking to enhance their operational efficiency.
Top Page Image Contents