Shure M97-xE manual Recommended Tonearm Setting Tracking Force

Page 1

 

Model M97xE User Guide

 

 

 

Cartridge installation

 

 

1.Carefully remove the stylus from the cartridge .

 

4. When the Dynamic Stabilizer brush is set to the op-

 

 

erating position A, it absorbs 0.5 grams of tonearm

 

 

tracking force. The proper tonearm settings for the

 

 

recommended range of stylus tip tracking forces are:

 

 

 

 

 

 

 

TRACKING FORCE (in grams)

 

 

RECOMMENDED

TONEARM SETTING

 

 

TRACKING FORCE

Dynamic Stabilizer

Dynamic Stabilizer

 

 

RANGE (effective at

Down (operating) A

Up (non-operating)

 

 

stylus tip)

 

B

 

 

Maximum 1.5 g

2.0 g

1.5 g

 

 

Optimum 1.25 g

1.75 g

1.25 g

 

 

Minimum 0,75 g

1.25 g

0.75 g

 

 

5. Make the following final adjustments. Consult your

 

 

turntable instructions.

 

1

 

Cartridge Overhang: If adjustable.

 

Anti-Skate: If this adjustment is not speci-

 

fied in your turntable instructions, use the

 

 

same setting as for tracking force.

Tonearm Height: If adjustable.

2.Connect the wires from the headshell to the pins on the cartridge . Use the following table for the correct connections. Note: To prevent “ground loops” and hum, do not make common (ground) connec- tions at these terminals.

R

RED

(RIGHT “HOT”)

RG

GREEN

(RIGHT GROUND)

L

WHITE

(LEFT “HOT”)

LG

BLUE

(LEFT GROUND)

2

3.Mount cartridge in the headshell and replace stylus (and ). Do not force. Note: screws can be threaded up from the bottom to provide maximum record clearance.

3

DYNAMIC STABILIZER/DE-STATICIZER

4

B

A guard

The M97xE’s exclusive viscous-damped Dynamic Sta- bilizer maintains a uniform distance between the car- tridge and the record under difficult playing conditions, such as those caused by warped records or mismatched tonearm mass. When such stabilization is not required, the stabilizer can be locked into its up position, which can improve sound quality under ideal playing conditions.

Over 10,000 conductive fibers in the stabilizer brush neutralize static charges on the record surface and con- duct them to the ground. Additionally, the fibers sweep the record groove clean of dust and dirt in front of the stylus tip. The Stabilizer also absorbs impact to pre- vent record or stylus damage if the arm is accidentally dropped on a record.

SIDE GUARD STYLUS PROTECTION SYSTEM

The Side-Guard stylus protection system helps prevent stylus damage if the cartridge accidentally slides across a record. This system responds to side thrusts on the stylus by withdrawing the entire stylus cantilever and tip safely into the stylus housing before the cantilever can be damaged.

Monophonic PLAYBACK

For monophonic playback of recordings, the left and right channels should be connected in parallel. This is ac-

complished most conveniently by setting the function switch on the associated preamplifier to “A + B” or “MONO.” If

the existing equipment has a single monophonic input, the two channels of the cartridge should be paralleled and connected to this single input.

CARTRIDGE OPERATION

1.

Make certain cartridge is correctly mounted in tone-

STYLUS CLEANING

 

arm and stylus is properly inserted in cartridge.

 

2. Protect stylus with stylus guard when dusting turntable.

5

3.

Regulate tonearm set-down to prevent stylus from

 

striking edge of turntable or record.

 

4.Do not handle tonearm while record is being played. Use cueing device if available.

5.If manual set-down is necessary, release arm as soon as stylus engages groove.

6. Do not activate arm without record(s) on turntable.

7. Do not use damaged records.

 

 

 

8. Check tracking force and anti-skate adjustments pe-

 

 

 

riodically. The Shure SFG-2 Tracking Force Gauge,

Use the supplied brush to clean the stylus and dynamic

available through your Shure dealer, provides a sim-

ple way to accurately set tracking force.

stabilizer. Brush only from back to front, as shown . Do

 

 

not use liquids on the stabilizer brush. Use alcohol or an

 

 

alcohol-distilled water solution to clean the stylus. Com-

 

 

mercial cleaning solutions may damage the stylus.

©2008, Shure Incorporated

 

 

 

27C3013 (Rev. 4)

 

 

 

Printed in U.S.A.

Image 1
Contents Recommended Tonearm Setting Tracking Force DE Lecture Sysème DE Protection Latérale DE LA PointeUtilisation DE LA Cartouche Nettoyage DE LA Pointe DE LectureInstalacion DE LA Capsula Eingeschränkte Zweijährige GewährleistungSistema SIDE-GUARD DE Proteccion DE Aguja Reproduccion Monofonica最適 1,25 g 75 g 最大 1,5 g最小 0,75 g 25 g

M97-xE specifications

The Shure M97-xE is a high-performance moving magnet cartridge that has earned a reputation among audiophiles and professionals for its exceptional audio quality and advanced features. With its rich heritage in sound reproduction, Shure has designed the M97-xE to provide a listening experience that is both engaging and accurate.

One of the standout features of the M97-xE is its advanced cartridge design, which incorporates a revolutionary dynamic stabilizer. This technology aids in tracking, ensuring that the needle maintains contact with the grooves of the record for optimal sound clarity. The dynamic stabilizer also helps to reduce distortion, especially during complex musical passages, ensuring a more nuanced and detailed audio experience.

The M97-xE features a highly sensitive and lightweight construction, which makes it suitable for a wide range of turntables. It has a nominal output voltage of 5 mV, allowing for strong signal levels without requiring excessive gain from the preamplifier. This sensitivity also contributes to its ability to capture the subtleties in music, from the most delicate acoustic notes to powerful orchestral crescendos.

Another important characteristic of the M97-xE is its elliptical stylus. The shape of the stylus allows it to more effectively trace the grooves of vinyl records, leading to improved frequency response and reduced wear on the records themselves. The elliptical stylus design ensures that high frequencies are reproduced accurately, while effectively managing surface noise and distortion.

In terms of durability, the M97-xE has a robust construction, designed for longevity and reliability. With a replaceable stylus, users can easily maintain the performance of the cartridge over time, making it a cost-effective choice for both casual listeners and serious collectors.

Additionally, the M97-xE comes with a number of useful accessories, including a stylus cleaning brush and a user-friendly installation guide. This makes it accessible for users of all experience levels, whether they are new to vinyl or seasoned professionals.

Overall, the Shure M97-xE offers a compelling combination of advanced technology, impressive sound quality, and durable construction. Its ability to deliver a rich, full-bodied sound while minimizing distortion makes it an outstanding choice for anyone looking to elevate their vinyl listening experience. Whether used for casual enjoyment or in a high-fidelity setup, the M97-xE stands out as a versatile and reliable moving magnet cartridge that continues to impress music lovers around the world.