Braun Complete Guide to Wheelchair Lift Manuals, Troubleshooting, and Parts for the Century and Millennium Series

LCD Lift Codes

Listed below are codes that the lift controller outputs during lift operation. The codes will be displayed RQDQ/&'VFUHHQORFDWHGRQWKHOLIWFRQWUROERDUG inside the pump module. See the Manual Operating Instructions in the operator's manual for pump cover removal instructions.

1RQ)ODVKLQJ1XPEHUV

01 – Platform stowed

02 – Platform unfolding

03 – Platform unfolding paused ²3ODWIRUPDWÁRRUOHYHO

05 – Platform beginning to lower

06 – Platform lowering (threshold cannot be occu- pied from this point down)

07 – Outer barrier moving to horizontal position

08 – Platform at ground level

09 – Outer barrier moving to vertical position

10 – Platform raising

²3ODWIRUPUDLVLQJSDXVHGDWÁRRU

12 – Platform folding (limited pressure)

13 – Platform folding (full pressure)

14 – Timed fold (cinching lift tite) or (anti-rattle state) 15 – Platform folding stopped

16 – Paused fold

17 – Platform between ground and 3” above ground

18 – Platform above 3”

19 – Outer barrier moving to horizontal postion

23Outer barrier going back down after occupant detected

²,OOHJDOIXQFWLRQQRWGHÀQHG

29 – Interlock fault not recognized (or has been cleared but a motion button is still pressed)

30 – Platform location unknown

31 – Platform location transition state; attempting to locate position

35 – Two or more motion buttons are being pressed 36 – The retention belt cannot be buckled while try-

ing to fold or unfold

37 – Motion button being pressed is not a valid mo- tion

50 – Outer barrier is not up above inboard barrier locked position

51 – Threshold is occupied when platform is 1” or

PRUHEHORZÁRRUOHYHO

52 – Inner rollstop is not up and locked below inner rollstop locked position

53 – Inner rollstop occupied sensor is not activated

EHWZHHQÁRRUDQGLQQHUUROOVWRSXSSRVLWLRQ 54 – Outer barrier is occupied before it is up

55 – Outer barrier is not latched when above the in- ner rollstop locked position (Millennium only)

56 – Outer barrier is not up and latched and bridge switch did not deactivate

57 – Outer barrier is not up and latched and ground detect switch did not deactivate (Century and Vista only)

58 – Outer barrier is not up and latched and the plat- form is 3” above the ground

59 – Outer barrier is not up after pausing platform travel

60 – The kickout gas springs are worn, replace before using

75 – Low voltage detected; must turn off power switch WRUHVHW/&'

77 – Vehicle secure interlock has not been activated 90 – Position will be set if you keep holding the button

until it beeps

91 – Position is out of a predetermined acceptable

UDQJHRIÁRRUSRVLWLRQ

92 – Bridge switch is not made, needs adjusting

93 – Inner rollstop occupied switch is not made, position needs to be moved or switch should be adjusted

²2XWHUEDUULHULVQRWPDGHÀ[DQGWU\DJDLQ

95 – Outer barrier latch is not made (check for jumper on Century and Vista lifts, check latch on Millen- nium lifts)

99 – Controller program is not valid; replace controller

)ODVKLQJ1XPEHUV

)ODVKLQJ²8QIROGEXWWRQLVSUHVVHG

)ODVKLQJ²)ROGEXWWRQLVSUHVVHG

)ODVKLQJ²'RZQEXWWRQLVSUHVVHG )ODVKLQJ²8SEXWWRQLVSUHVVHG )ODVKLQJ²%ULGJHVZLWFKLVDFWLYDWHG )ODVKLQJ²2XWHUEDUULHUODWFKVZLWFKLVDFWLYDWHG )ODVKLQJ²*URXQGGHWHFWVZLWFKLVDFWLYDWHG )ODVKLQJ²2XWHUEDUULHUXSVZLWFKLVDFWLYDWHG )ODVKLQJ²,QQHUUROOVWRSXSVZLWFKLVDFWLYDWHG )ODVKLQJ²,QQHUUROOVWRSRFFXSLHGVZLWFKLVDFWL-

vated )ODVKLQJ²2XWERDUGEDUULHURFFXSLHGVZLWFKLV

activated )ODVKLQJ²7KUHVKROGWDSHVZLWFK´$µLVDFWLYDWHG )ODVKLQJ²7KUHVKROGWDSHVZLWFK´%µLVDFWLYDWHG )ODVKLQJ²3RVLWLRQVHWEXWWRQLVSUHVVHG

Page 11