Description
Block, Platform Stop - Bridging - Rear
Block, Platform Stop - Bridging - Front Snap-Ring 5/16"
O-Ring, 5/16" I.D. x 1/16" O.D.
Screw, Socket Head, 3/8-16 x 1/2" with 1/2" Shoulder Grommet, I.D. .281"/ FR.125" x GD.625"/T.375" Pivot, Outer Barrier Lever
Slide, UHMW, Platform Rotate Stud, Wing Head
Retainer, Push-On
Grommet, ID .312", FR .250", GD .813" T500" Pump Assembly
Pin, Pivot, Parallel Arm
Screw Drive #8 x 3/16" Long Black Receptacle, Clip-On
Cylinder, Outer Barrier
Screw, 10-32 x 5/8" Pan Head Phillips, Thd. Cut Latch, Outer Barrier w/Magnet
Bolt, 5/16-18 x 1/2" Nylock, Hex Washer, 5/16" Flat
Bolt, 3/8-16 x 1/2" Nylock, Hex Assembly, IB Occupied Assembly, Rotary Position Sensor Bolt, 5/16-18 x 3/4" Nylock, Hex Rivet, Pop, SD68 BSLF-3/16" - .38"/.50" Rivet, Pop, 1/8"- .25"/.31"
Bearing, Flange, 1/2" x 1/4" Weldment, Latch, Lift/Tite, Rear Weldment, Latch, Lift/Tite, Front Screw, #4-40 x 5/8", Round Head
Screw, 1/4-20 x 3/4", Flat Head, Countersink Screw, #8-32 x 1", Mach. Truss Head
Nut, #4-40 w/Lockwasher Nut, #8-32, Hex
Bag, Vinyl - 7" x 10"
Cylinder, 14.625"/29.146" Retracted
Adapter, Cylinder/Outer Barrier Lever Washer, External Tooth
Washer, Finger, Disc Spring
Vertical Channel Weldment, Front, 48" Cover, Plastic, Parallel Arm, O/S Front-w/Tape Tape, 1" Wide S-Face Foam, x 14" (1 Shown) Tape, 1" Wide S-Face Foam, x 10" (3 Shown) Cycle Counter-LCD Without Reset Handrail Weldment
Rivet, Push In - 8MM Bumper, Rubber, 31/32" O.D. Screw, #8-18 x 1/2", Self-Tap, Phillips %XOE/LJKW:+DORJHQ5HÁHFWRU Nut, #10-32 w/Lockwasher
Screw, 1/4-20 x 3/4", Button Head, Socket Cap Washer, 3/8" Flat, Black
Nut, 3/8-16, Hex Lock Cotter Pin, 1/4" x 2", Black Nut, 1/4-20 Hex Lock
Cover, Plastic, Parallel Arm, I/S Front-w/Tape Threshold Strip Switch
Bolt, Shoulder, 5/16 x 5/8-1/4"-20 Washer, #10, Flat, Auto BK Washer, 1/2" Flat Black Zinc Bolt, 3/8-16 x 1", Hex Washer, 3/8", Lock, Black Lever, Inner Rollstop
Clamp, Insulate, 1 3/8" I.D.
Washer, 5/16" Lock, Black Gas Spring, Fold Arm
Ball Stud, Gas Spring, 13MM x 3/8-16 F. Thread Washer, 3/8", Lock
Spacer, Flap Cylinder .184" Thick
Clip, Safety, 3/8-16 x 3/4", Flange
Bolt, 3/8-16 X 3/4", Flange Button Head, Socket Cap Bolt, 5/16-18 x 2", Flange, Hex
Nut, 5/16-18, Serrated Flange Arm, Slide Support
Slide, Platform, Rotate
Spacer, .5" O.D. x .334" I.D. x 1.515" LG Bearing, Flange, 3/4" x 1/4"
Weldment, Platform Pivot Arm - 48" Pin, Pivot, Lower Arm
Ring, Snap, 3/4", External Bearing, UHMW, Flat, 1.226" Ball Stud, 10MM
Vertical Channel Weldment, Rear, 48"
Plastic End Cap, 1" I.D. x 1 1/4" O.D. Grip, Handle, Yellow
Description
Spring, Dampener, Retract
Bolt, 5/16-18 x 1 1/4" Low Socket Hd., Cap, Bk. Bumper, .75"x .625" Long
Screw, 1/2-20 x 1 1/2" Set Lock, Black Block, Guide-Platform Stow
Pin, Platform
Screw, 5/16-18 x 3/4", SHFS Spacer, UHMW, Vertical Channel Position Sensor Collet Bracket, Mounting, Quiet Ride
Gas Spring, 12.2" Extended/8.3" Compressed Bolt, 5/16-18 x 3/4", Carriage, Black Washer, 5/16", External Tooth
Nut, 5/16-18 Hex
Bracket, Inner Side Panel Guide
Bearing, UHMW, Flat, Thin, Black
Pivot, Inner Rollstop Lever, Upper, Inside Bearing, Flange - 3/4" x 1/2"
Spacer, UHMW, Latch
Spring, 1/4" x 1" Extension w/Hooks
Tubing, Polyurethane - 1/4" I.D. x 1/2" O.D. x .81" Pin, Clevis, 3/8" x 3", Black
Pin, Platform Cylinder
Ring, Snap, 1/2", External, .035" Thick Weldment, Tube-IB Fold Arm-Rear
Lever, Outer Barrier Latch (Assembly #915-0345A) Nut, 3/8-16, Hex
Weldment,Tube-IB Fold Arm-Front
Pivot, Outer Barrier Cylinder, Front
Bolt, 5/16-18 x 1 1/2" Hex Head, Cap Bolt, 7/16-20 x 1", SHCS, w/Nylock Patch Screw, #10-32 x 3/8", Flat Head, Hex Adapter, Cylinder/Outer Barrier Lever-Out Bolt, 5/16-18 x 3/4", Button Head, Soc Cap Hd Rivet, Pop, 3/16"-.25"/.38", Black
Adapter, Cylinder/Outer Barrier Lever Harness, Sensor - Cherry w/Plug Screw, #4-40 x 1/4" Phillips Head Clamp, Cable, 1/2", Plastic
Nut, 5/16-18, Top Lock, Black
Bolt, 1/4-20 x 1/2", Button Head Socket Bolt, 3/8-16 x 2", Hex Head, Cap Roller Assembly
Roller Retainer
Nut, 5/16-18 Hex, Lock
Pivot, Inner Rollstop Lever, Upper-Outer Clamp, 1/4" I.D.- Nylon Loop
Clamp, 5/8" Closed Insulated Rivet, Snap, .201" x .256"/.295" Bearing, Flange, 1" x 1/2-16FDU08
Cover, Plastic, Parallel Arm, O/S Rear-w/Tape Weldment, Inner Rollstop Bracket, Front Spacer, Handrail, .375” Thk. UHMW Washer, .516" I.D. x .75" O.D. x .250", Black Cover, Plastic, Parallel Arm, I/S Rear-w/Tape Weldment, Inner Rollstop Bracket, Rear Spring, Torsion - .366 I.D. x .05"
Spacer, IB Lock Weldment, IB Lock Bearing, 3/8" I.D. x 1/2" Long Roller, .65" O.D. x 1/2" Long E-Clip, 3/8" Shaft
Spacer, Handrail, .230" Thk. UHMW Washer, .516" I.D. x 1"/O.D. x .269", Auto BK Rivet, Pop, 3/16" - .13/.25" - SD64BS Rivet, Pop, 3/16" x .06"/.13
Bearing, Flange, 3/8" x 1/4" - Plastic Light Assy, Vertical Channel
Tab, Outer Barrier, Flap Cylinder w/Magnet Washer, .4" I.D. x .810" O.D. x .12" Spacer, UHMW-.75" O.D. x .39" I.D. x .25" Bolt, 3/8-16 x 3/4" Soc. Hd. Cap Screw Bk. Spacer, Flap Cylinder .700" Thick Guard, Outer Barrier Sensor Wires Snap-Ring 1/2"
Screw, #10-32 x 1/2" Button Head, Socket, Cap Position Sensor Spacer
Weld Nut, #4-40 x 1/8" Barrel
