Invacare Infinity LoBack Support INSTALLING/REMOVING the Lateral Supports Figure, Installing

Page 7

PREPARING THE INFINITY LOBACK FOR INSTALLATION

PROCEDURE 2

This Procedure includes the following:

Installing/Removing the Lateral Supports

Installing/Removing the Back Cushion

Installing/Removing the Lower Flap

INSTALLING/REMOVING THE LATERAL SUPPORTS (FIGURE 1)

WARNING

After ANY adjustments, repair or service and BEFORE use, make sure that all attaching hard- ware is tightened securely - otherwise injury or damage may result.

NOTE: Refer to the INSTALLATION AND STABILITY WARNINGS in the SAFETY SUMMARY of this manual.

Installing

NOTE: The final mounting positions of the lateral sup- ports will be determined by the adjustments made to the Infinity LoBack to fit the wheelchair and user.

1.Remove the back cushion from the back panel. Re- fer to INSTALLING/REMOVING THE BACK CUSH- ION in this procedure of the manual.

NOTE: The lateral supports can be adjusted to three (3) different height positions (DETAIL “A”).

2.Align the upper, middle or lower mounting holes in the lateral support with the toothed adjustment slots in the back panel (DETAIL “A”).

NOTE: The grooves next to the mounting holes in the lateral supports are provided to ensure that opposite lat- eral supports are installed using the SAME mounting holes (FIGURE 1). To ensure that this occurs, install one (1) lateral support at the desired height and look through the toothed adjustment slot to see which mounting holes have been used. Then, install the opposite lateral support us- ing the SAME mounting holes.

3.Install the two (2) mounting screws and washers that secure the lateral support to the back panel. Hand tighten ONLY.

NOTE: It is NOT necessary to tighten the mounting screws on the lateral support at this time. The lateral supports will be adjusted AFTER the Infinity LoBack has been installed on the wheelchair and the user has been evaluated.

4.Repeat STEPS 2-3 to install the OPPOSITE lateral support.

5.Reinstall the back cushion onto the back panel. Re- fer to INSTALLING/REMOVING THE BACK CUSH- ION in this procedure of the manual.

Removing

1.Remove the back cushion from the back panel. Refer to INSTALLING/REMOVING CUSHIONS in this pro- cedure of the manual.

2.Remove the (2) mounting screws and washers se- curing the lateral support to the back panel.

3.Remove the lateral support.

4.Repeat STEPS 2-3 for the remaining lateral supports, if necessary.

DETAIL “A”

Upper

Lateral

Support

Mounting

 

Holes

 

 

Middle

 

Mounting

Lower

Holes

 

Mounting

 

Holes

 

Toothed

Adjustment

LateralSlot

Support

Grooves

Mounting

Back Panel

Screws

FIGURE 1 - INSTALLING/REMOVING THE

LATERAL SUPPORTS

P R E P A R I N G

T H E

L O B A C K

F O R

I

N S T A L L A T I O N

7

Image 7
Contents InfinityTM LoBackTM Support Special Notes Safety Summary Safety SummaryStability Warnings Important INFORMATION/INSTALLATION/ADJUSTMENT Overview INSTALLATION/ADJUSTMENT Overview FigureRemoving Cane Clamps Preparing WheelchairRemoving INSTALLING/REMOVING the Lateral Supports FigurePreparing the Infinity Loback for Installation InstallingProcedure INSTALLING/REMOVING the Back Cushion FigureINSTALLING/REMOVING Modesty Flap INSTALLING/REMOVING the Modesty Flap FigureInstalling the Infinity LoBack INSTALLING/REMOVING the Infinity Loback FigureRemoving the Infinity LoBack Adjusting the Cane Clamps Figure Adjusting the Depth HardwareAdjusting the Mounting HARDWARE/HEIGHT Figure Adjusting the Infinity LobackPivoting The Adjustment Brackets Figure Adjusting the Infinity LobackAdjusting the Lateral Supports Adjusting the Angle FigureAdjusting the Width Figure Adjusting the Height Figure Adjusting the HeightInspection CleaningMaintenance Replacing the Back Cushion Foam FigureLimited Warranty