NetComm 5340 manual Reconnecting power to the telephone

Page 3

sUsing the same screw that you removed from the phone in step o, screw the Cordless Module to the back of the phone.

CAUTION: The screw provided with the phone is sized so that it does not damage the interior mechanisms of the phone. Using any other screw to attach the module may damage the phone.

If you are connecting a handset and/or headset, do not connect the power at this point. Proceed with the following instructions:

Attaching the Cordless Handset and Charging Cover to the 5330 or 5340 IP Phone (See Figure B )

Disconnect the LAN power supply cable from the back of the phone if you have not already done so. Detach the corded handset from the phone if installed.

Remove the cover on the front of the phone at the bottom of the handset cradle by removing the retaining screw inserted from the back of the phone. Keep the screw in a safe place—you must re-use this screw.

nBring the new charging cover to the phone and plug the power jumper cable

into the connector in the phone.

oInsert the lip on the right side of the cover into the slot on the phone and snap the cover into place.

pUsing the same screw that you removed from the phone in an earlier step, screw the cover to the back of the phone. Place the Cordless Handset in the phone cradle.

NOTE: The cordless handset must be fully charged before use. This will typi- cally take 3 hours. A new, fully-charged handset battery has a talk time of 8 hours.

Attaching the Cordless Headset and Charging Cradle to the 5330 or 5340 IP Phone (See Figure C )

Disconnect the LAN power supply cable from the back of the phone if you have not already done so.

Remove the two screws on the back of the phone that hold the side backplate, but do not remove the backplate.

nInstall the Headset Charging Cradle on the back of the phone and, using the

screws provided with the charging cradle, screw it to the phone.

oConnect the Headset Charging Cradle cable to the jack on the Cordless Module. Place the Cordless Headset in the charging cradle.

NOTE: The cordless headset must be fully charged before use. This may take up to 3 hours. A new, fully-charged headset battery has a talk time of 8 hours.

Reconnecting power to the telephone

Reconnect to the power supply by plugging the LAN cable into the LAN port on the back of the phone. Remember to thread the LAN plug through the slot on the phone’s base unit, so that the base unit sits level.

NOTE: Mitel-supplied power adapters are the only adapters qualified by Mitel for connection to the 5330 and 5340 IP Phones.

Notice to Canadian Customers

Industry Canada Certification Numbers:

-Cordless Module: IC: 173A-MODULE1

-Cordless Handset: IC: 173A-DECT1

The term “IC:” before the certification/registration number only signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that industry Canada approved the equipment.

Operation of this device is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

This Class B digital apparatus complies with Canadian ICES-003.

Notice to U.S. Customers

FCC IDs:

-Cordless Module: EHTMODULE1

-Cordless Handset: EHTDECT1

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment gener- ates, uses, and radiates radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference. However, there is no guarantee that interference will not occur. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interfer- ence by one of the following measures:

Reorient or relocate the receiving antenna.

Increase separation between the equipment and receiver.

Connect the equipment to an outlet on a circuit different from which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

NOTE: The Cordless Handset is hearing aid compatible.

WHEN PROGRAMMING EMERGENCY NUMBERS AND (OR) MAKING TEST CALLS TO EMERGENCY NUMBERS

Remain on the line and briefly explain to the dispatcher the reason for the call.

Perform tests during off-peak hours such as early morning or late evenings.

RF Exposure

This device has been evaluated under FCC bulletin OEC65C for RF Radiation Exposure and found compliant to the requirements as set forth in CFR47 section 2.1091 and section 2.1093 addressing RF exposure from Radio frequency devices.

This device is compliant to the RF exposure requirements in Industry Canada RSS-102 issue 2.

WARNING:To ensure compliance with FCC and Industry Canada RF exposure requirements, the cordless module must be installed to provide a separation distance of at least 20 centimeters from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

Notice to Customers in Australia

• Do not use in areas where there are explosive hazards.

ACA TS 028 - Ignition of flammable atmospheres

Do not use the cordless handset in environments where there is a danger of ignition of flammable gases.

3

Image 3
Contents Cordless Module and Accessories This symbol may appear on the product Safety Instructions for the Cordless HandsetFrom the drop-down list, select User Guides Reconnecting power to the telephone Avertissement Ce symbole peut figurer sur le produitÉvitez dexposer le produit à la pluie ou à dautres liquides Consignes de sécurité relatives au combiné sans filInstructions de sécurité pour le combiné sans fil Precaución Instrucciones de seguridad para el auricular inalámbricoPeligro AdvertenciaInstrucciones de seguridad para auriculares inalámbricos Puede aparecer este símbolo en el productoEvite expor o produto à chuva ou outros líquidos Este símbolo poderá estar no produtoInstruções de segurança para o aparelho sem fio Aviso Evitar a exposição do produto à chuva ou a outros líquidosPossível que os seguintes símbolos apareçam no produto Instruções de Segurança do Auscultador Sem FiosDas folgende Symbol kann auf dem Produkt angebracht sein Wichtige Sicherheitshinweise und Vorsichtsmaßnahmen DeutschSicherheitshinweise für den schnurlosen Hörer Istruzioni e precauzioni per la sicurezza Italiano Questo simbolo può essere presente sul prodottoIstruzioni per la sicurezza del ricevitore cordless Waarschuwing Dit symbool wordt mogelijk op het product weergegevenVeiligheidsinstructies voor de draadloze telefoon Gevaar

5340 specifications

The NetComm 5340 is a versatile router designed to meet the connectivity needs of modern homes and small businesses. Known for its robust performance and advanced features, it provides a reliable networking solution for users who demand speed and stability.

One of the primary features of the NetComm 5340 is its dual-band capability, which supports both 2.4GHz and 5GHz frequency bands. This dual-band functionality allows for greater flexibility in managing network traffic. The 2.4GHz band offers wider coverage and better penetration through walls, making it ideal for basic internet browsing and connecting older devices. Meanwhile, the 5GHz band delivers faster speeds, making it suitable for bandwidth-intensive applications such as streaming high-definition content and online gaming.

The router is equipped with the latest wireless standards, offering Wi-Fi 5 (802.11ac) technology. With this technology, users can experience enhanced data throughput and improved performance in crowded environments. The NetComm 5340 also features multiple Gigabit Ethernet ports, enabling wired connections for devices that require stable connectivity, such as smart TVs, gaming consoles, and desktop computers.

Security is a crucial aspect of the NetComm 5340, which comes with advanced cyber protection features. It includes WPA3 encryption, the latest security protocol that ensures secure communications over the wireless network. Additionally, it is equipped with a built-in firewall and supports advanced security measures such as SPI (Stateful Packet Inspection) and DoS (Denial of Service) attack prevention, providing a multi-layered approach to safeguarding users’ data.

Another key characteristic of the NetComm 5340 is its ease of use. The device is user-friendly, with a straightforward setup process that allows users to get connected quickly. The intuitive web-based interface offers an array of configuration options, letting users personalize their network settings based on their specific needs.

For those needing to manage their network effectively, the NetComm 5340 includes support for Quality of Service (QoS) features. This allows users to prioritize bandwidth for specific applications or devices, ensuring that critical tasks remain uninterrupted, even during peak usage times.

Overall, the NetComm 5340 is a robust and feature-rich router that caters to the growing demands of internet users. Its combination of dual-band technology, strong security features, and user-friendly design positions it as an excellent choice for anyone looking to enhance their home or office networking experience.