Included in Your Package | Teledex AC8205S, AC9205S instruction

iPhone DECT Cordless Series User Guide

For Models AC8205S, AC8210S (1.8 GHz) and AC9205S, AC9210S (1.9 GHz)

Included in Your Package
Cordless Handset	Rubber Battery Screw Cover
AC Adapter	Phillips Screw
Base Unit	15-foot, 8-wire Cable
User Guide	(with RJ-45 connector)
Lithium Polymer Battery	10-foot, 4-wire Line Cord
Clear Plastic Overlay	(with RJ-11 connector)

Preparing to Use the AC8200/AC9200 Series

1.Prepare to install the battery into the cordless handset by removing the battery cover and sliding it off. If cover is secured with a screw, remove the screw first.

2.Insert the battery connector into the handset’s connector. The connector is “keyed” so it only goes in one way.

Do not force the connection.

Note: The handset may “beep” when the battery is connected. This is not an indication that the telephone is ready to use. To obtain optimal performance of the telephone, be sure to charge the battery for 10 to 12 hours.

3.Replace the battery compartment cover and the retaining screw.

4.Insert the provided rubber screw cover.

5.Turn the telephone base so the back panel is facing you. Insert either end of the RJ-45 cable into the jack on the back of the telephone labeled LINE.

6.Insert the other end of the cable into the jack on the AC adapter labeled PHONE.

7.Insert one end of the RJ-11 line cord into the jack on the AC adapter labeled LINE.

8.Insert the other end of this line cord into a telephone jack.

9.Plug the AC adapter into an unswitched electrical outlet.

10.Remove the plastic overlay and place the paper faceplate (supplied separately) over the keys. Replace the plastic overlay by hooking the tabs on the overlay into the recessed slots located on both sides.

11.Place the cordless handset on the base unit. The handset/base registration process will occur.

Handset/Base Registration Procedure

This procedure establishes an exclusive link between a specific handset and base, thereby allowing no other access to this specific base. To accomplish this procedure, place the handset on the base in the charging position. The LINE indicator will blink while the registration process is occuring. This process only occurs the first time a handset is placed on the charging cradle of a new base.

Charging the Battery

The rechargeable Lithium-Polymer battery must be fully charged before using the phone for the first time.

It is recommended that the battery be charged for approxi- mately 10 to 12 hours without interruption before use.

To charge the battery, place the handset, keypad down, in the base unit. Ensure that the CHARGE LED on the base lights.

If the LED Does Not Light:

1.Ensure that the AC adapter is plugged in.

2.Ensure that the AC adapter is plugged into an unswitched electrical outlet.

3.Ensure that the handset charging contacts at the bottom of the handset are making good contact with the base unit’s charging contacts.

Cleaning the Battery Contacts

To maintain a good charge, it is important to clean all charging contacts on the handset and base unit. Use a pencil eraser or other contact cleaner. Do not use any liquids or solvents.

Battery Safety Instructions

1.Use only Teledex-approved battery replacements.

2.Dispose of the Lithium-Polymer battery in any ordinary trash receptacle.

3.Do not dispose of battery in fire, as it may explode.

4.Charge the battery only while in the handset, and only by using the base unit to charge. Do not attempt to remove the battery and charge it in a separate charging unit.

5.Do not short-circuit the battery, as this may cause it to explode or catch fire.

Adjusting the Ring Volume and Assigning Ring Tones

The UP and DOWN volume keys will adjust the ringer volume of the telephone. To adjust ring volume, press either the UP and DOWN volume key when the handset is on the bse cradle and the phone is not active (off-hook).

There are four ring tones that can be assigned individually to either line (on two-line models) to audibly identify the ringing line. Additionally, the AC8200/AC9200 series features a programmable “crescendo” ring mode, wherein the ring volume begins at the lowest setting, then rings progressively louder with each ring during an incoming call.

To assign a ring tone to a line (normal ring mode):

1.Press the FLASH key (see Fig. 1); then a key on the dial pad from 1-4, depending on the desired ring tone. The phone will ring once to provide a sample of the selected ring tone.

2.When you have selected a suitable ring tone, press the STORE key (see Fig. 1), then a number on the dial pad for the desired line assignment (i.e.; ‘1’ for line 1, ‘2’ for line 2).