7) Insert the top two retaining tabs of the mounting brackets into | phone company must; promptly notify you of such temporary discontinuance; afford the opportuni- | |
the mounting bracket slots (located near the middle of the tele- | ty to correct the condition; inform you of your rights to bring a complaint to the FCC under their | |
rules. | ||
phone). Then firmly push down to insert the retaining tabs on | 6. Repairs to the device may be made only by the manufacturer or an authorized service agency. | |
the opposite side of the mounting bracket. | This applies at any time during and after warranty. If unauthorized repair is performed, registration, | |
8) Connect a short modular line cord into the jack on the back of | connection to the telephone lines and remainder of warranty period all become null and void. | |
7. This equipment is hearing aid compatible. | ||
the phone (labeled TO TEL). Route the line cord through the line | ||
REQUIREMENTS OF PART 15 - FCC RULES | ||
cord channel. Connect the other end of line cord to the phone | ||
jack on the wall mounting plate. | NOTE: This equipment has been tested and found to comply with the limits for a Class B digital | |
9) Turn the telephone over, and slide the Diamond down onto the | device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable pro- | |
tection against harmful interference in a residential installation. This equipment generates, uses, and | ||
wall plate mounting posts. Both eyelets should line up with the | can radiate radio frequency energy and, if not installed and used in accordance with the instruction, | |
mounting posts (When properly installed the telephone will be | may cause harmful interference to radio communications. However, there is not a guarantee that | |
stable and secure). | interference will not occur in a particular installation. If this equipment does cause harmful interfer- | |
ence to radio or television reception, which can be determined by turning the equipment off and on, | ||
10) Complete the wall mounting by installing the handset and hand | the user is encouraged to try to correct the interference by one or more of the following measures: - | |
set cord. | Move the telephone away from the receiver. | |
cian for help. Any changes made by the user not approved by the manufacturer can void the user's | ||
| authority to operate the telephone. | |
| INDUSTRY OF CANADA REQUIREMENTS | |
REQUIREMENTS OF PART 68 - FCC RULES | Notice: The Industry Canada label identifies certified equipment. This certification means that the | |
equipment meets certain telecommunications network protective operational and safety requirements | ||
This device has been granted a registration number by the Federal Communications Commission, | as prescribed in the appropriate Terminal Equipment Technical Requirements documents. The | |
under Part 68 rules and regulations for direct connection to the telephone lines. In order to comply | department does not guarantee the equipment will operate to the users satisfaction. | |
with these FCC rules, the following instructions must be carefully read and applicable portions fol- | Before installing this equipment, users should ensure that it is permissible to be connected to the | |
lowed completely: | ||
facilities of the local telecommunications company. The equipment must also be installed using an | ||
1. Direct connection to the telephone lines may be made only through the standard modular cord fur- | ||
acceptable method of connection. | ||
nished, to the utility installed jack. No connection may be made to party or coin phone lines. On | The customer should be aware that compliance with the above conditions may not prevent degrada- | |
the bottom of the phone is a label that contains among other information, the FCC Registration | ||
tion of service in some situations. | ||
Number and the Ringer Equivalence number (REN) for this equipment. If requested this informa- | ||
Repairs to certified equipment should be coordinated by a representative designated by the supplier. | ||
tion must be provided to the telephone company. The USOC Jack for this equipment is RJ11C. | ||
Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give | ||
2. The telephone company, under certain circumstances, may temporarily discontinue and make | ||
the telecommunications company cause to request the user to disconnect the equipment. | ||
changes in facilities and services which may affect the operation of the users' equipment: however, | ||
Users should ensure for their own protection that the electrical ground connections of the power utili- | ||
the user shall be given adequate notice in writing to allow the user to maintain uninterrupted serv- | ||
ty, telephone lines, and internal metallic water pipe systems, if present, are connected together. This | ||
ice. | ||
precaustion may be particularly important in rural areas. | ||
3. In certain circumstances, it may be necessary for the telephone company to request information | ||
Caution: Users should not attempt to make such connections themselves, but should contact the | ||
from you concerning the equipment which you have connected to your telephone line. Upon | ||
request of the telephone company, provide the FCC registration number and the ringer equiva- | appropriate electric inspection authority or electrician, as appropriate. | |
lence number of the equipment which is connected to your line; this information will be found on | The Ringer Equivalence Number (REN) of this device is Z. | |
the device. | Notice: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indi- | |
4. If any of your telephone equipment is not operating properly, you should immediately remove it | cation of the maximum number of terminals allowed to be connected to a telephone interface. The | |
from the telephone line. It may cause harm to the telephone network. | termination on an interface may consist of any combination of devices subject only to the require- | |
5. If the telephone company notes a problem, they may temporarily discontinue service. When practi- | ment that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5. This | |
telephone connects to the telephone network under the connecting arrangement code CA11A. | ||
cal, they will notify you in advance of disconnection. If advance notice is not feasible, the tele- | ||
| ||
|
|
TELEDEX DIAMOND DIAGRAM
RING VOLUME
Adjusts the ringer volume to Low or High setting.
HANDSET HOLDER
Used to temporarily hold the handset, without hanging up the telephone, when telephone is wall mounted.
HEARING AID COMPATIBLE HANDSET
HANDSET RETAINING CLIP
This removable clip can be rotated 180 degrees to allow handset to stay on hook when used in wall mount applications.
HANDSET JACK
Modular jack for connecting handset to base.
DIAL KEYS (DTMF PAD)
For dialing phone numbers, and entering numbers to be stored in auto dial keys.
DATA PORT
MESSAGE WAITING LIGHT
Signals that a message is waiting for retrieval. See your system administrator for instructions on retrieving messages.
HANDSET VOLUME KEY
Changes handset volume by pressing repeatedly.
| FOR CUSTOMER SERVICE CALL |
Part Number |
Teledex, LLC | Telephone: | (408) |
6311 San Ignacio Avenue | Fax: | (408) |
San Jose, CA | email: | sales@teledex.com |
95119 | Internet: | www.teledex.com |