Oricom ECO90 manual From HANDSETS 2ECONNECT After TMINUTES

Page 30

28TROUBLESHOOTING GUIDE

Problem	Possible cause(s)	Solution(s)

"ADAAUDIOAQUALITYO	1. Interference from nearby electrical appliance.	1. Try a different connection point, one that is away from other
(crackles,echo, etc.).	2. Base unit is installed in a room with thick walls.	electrical appliances.
	3. The handset is too far from the base unit.	)NSTALLTTHELBASE UNITEIN A $)&&%2%.4 ROOMT/2 USE
	)F YOU HAVEE"ROADBAND!$3, YOU NEEDNAEIN LINEA	EXTENSION leads.
	)F YOU HAVEE"ROADBAND!$3, YOU NEEDNAEIN LINEA	-OVEE#,/3%2 TO3THE2BASE UNIT
	ﬁlter (not supplied).	-OVEE#,/3%2 TO3THE2BASE UNIT
		%NSURE A INLINE !$3,NlLTERIIS INSTALLED ON ALLLPHONERSOCKETST
		between wall plate and your phone.

#ALLER )$EDOES NOT WORK	Service not activated.	#HECKKYOURU35"3#2)04)/. WITH)THE43%26)#% PROVIDER

Phone does not ring when	1. The ringer is off.	1. Turn ON the ringer.
a call comes in.	2. Too many phones are sharing the same phone	$ISCONNECT SOMEEOF THE PHONESEFROM THE PHONE LINE
	line.	3. Check base unit CONNECTIONS.
	3. Base unit not plugged in.

Keypad does not work.	Keypad may be locked.	UNLOCK the keypad.

Busy tone + in use light on.	1. Other handset may still be connected.	#HECKK!,,!HANDSETS AND %.$ ALL CALLS
	2. Check power supply connection.	2. Check CONNECTIONS to wall and base.

Handset registration fails	The base memory may be full.	$ELETE UNUSED HANDSET AND TRYYAGAIN
continuously.

#ANNOT MAKEANSWERRA ND	2nd call service can be activated.	Check with your service provider. Check the recall selection is
call		correct.

Note:

If none of the above solutions help, reset your phone by disconnecting the mains power from the base and removing batteries

FROM HANDSETS 2ECONNECT AFTER TMINUTES

Image 30

Contents Oricom eco90 Series Table of Contents Mean power of this telephone does not exceed M7 Limit Atiwhichtpointttestingiis REQUIRED2EFER to Information Contained INN7HITEIPAGES DIRECTORY Installation and Charger Getting Started Nsertt Rechargeable Pack contents Purchasing additional handsetsFeatures Your cordless handsetYour Base unit LED state ,%$%ON Basenstation LCD Display Icon DescriptionBasic Operation Muting the Microphone Switching the Keypad Lock On/OffDialling from the Phone Book Paging the Handset Button and the first entry in the phone book appearsIntercom MULTI-HANDSET OperationMulti-Handset operation Call TransferRedial Operation Caller ID Operation Caller ID Service 9OU Willwhear a Service Tone then 0RESS Call waitingDelete a Single Call Log Record Review Call Log RecordSave Call Log Record Delete All Call Log RecordDial back from a Call Log Record Phone Book Store EntriesPress key to select a desired entry, and then Edit Entries Delete EntriesDelete All Entries Edit or Or keys for 1.5 seconds will store the shown number9OU can SET Twooalarms on THENHANDSET AlarmsRing Volume Menu OperationSet Date Using the keypad, press key to confirm the settingDate / Time format 9OU can SET the $ATE4IME FORMATADISPLAYEDEarpiece Boost Mode Set Time% 3%44.3v Presse key, then press + or Backlight Setting Key Tone Handset NameDisplay Contrast Language Set DefaultAuto Talk Base Ringer MelodyBase Ringer Volume Change PIN%v and Press key Recall Flash Time VmwiSelect Base RegistrationRegister 2EGISTERINGNYOURUHANDSETPress key Input the PIN code and press key Remove HandsetRemove Base Want to remove and press keyTechnical Specifications For guidance only, depends on initial battery chargeTroubleshooting Guide TroubleshootingFrom HANDSETS 2ECONNECT After TMINUTES PRODUCT Warranty Information AustraliaAppendix Failure LIGHTINGHOVER VOLTAGEAustralia Customer Support