Verve 100 – Edition 5 – 18.8.00 – 3250
Verve 100 – Edition 5 – 18.8.00 – 3250
Verve 100 – Edition 5 – 18.8.00 – 3250
Verve 100 – Edition 5 – 18.8.00 – 3250 | Verve 100 – Edition 5 – 18.8.00 – 3250 |
Verve 100 – Edition 5 – 18.8.00 – 3250
At a glance
|
|
|
| Handset button | |
|
|
|
| Used to make and | |
|
|
|
| receive calls. | |
Display |
|
|
| Redial | |
Displays the |
|
|
| Lets you redial the | |
status of the |
|
|
| last number you | |
handset. |
|
|
| called. | |
Speed dial |
|
|
| Key lock | |
Used in conjunction |
|
|
| Lets you lock | |
with the Set button |
|
|
| (and unlock) | |
to store and access |
|
|
| the key pad to | |
numbers. |
|
|
| prevent accidentally | |
| 1 | 2ABC | 3 DEF | pressing buttons. | |
Recall |
| ||||
4 GHI | 5 IKL | 6MNO | Set | ||
For use with | |||||
7PQRS | 8TUV | 9WXYZ |
| ||
switchboards | To access your | ||||
|
|
| |||
and BT Select | ✱ | 0 | # | phone’s functions. | |
Services. |
|
|
| To store numbers | |
Press and hold | R |
|
| ||
|
| in the memory. | |||
|
|
| |||
down to enter |
|
|
|
| |
a Pause. |
|
|
|
|
Safety information
General
Only use the power supply included with the product. Using an unauthorised power supply will invalidate your warranty and may damage the telephone.
Ensure that the battery is fitted correctly. The red wire should be connected to the positive terminal (+) and the black wire to the negative terminal
Replacement batteries can be obtained via the BT Helpline on 0845 790 8070.
If the key lock is active, it is not possible to make emergency calls to 999 and 112.
Do not open the handset or base station. This could expose you to high voltages or other risks. Contact the Helpline for repairs.
Radio signals transmitted between the handset and base may cause interference to hearing aids.
This product should not be used near emergency/ intensive care medical equipment and should not be used by people with pacemakers.
Never dispose of batteries in a fire. There is a serious risk of explosion and/or the release of highly toxic chemicals.
Do not hold the handset to your ear during the incoming ring tone.
Environmental
Do not expose to direct sunlight.
The product may heat up when the batteries are being recharged. This is normal. However, it is recommended that you do not place the product on antique/veneered wood to avoid damage.
Setting Up
Plan the location
Situate your product close enough to the telephone socket and mains power supply so that the cables will reach.
Make sure it is at least 1 metre away from other electrical products to avoid interference.
Note
The range of your handset is 30m indoors and approximately 200m outdoors. If the 
icon flashes on the display you could be out of range and should move closer to the base station.
1Connect the power cable
Plug the power cable into the power socket on the underside of your Verve 100.
2Plug the power adaptor into a mains power socket and switch on
3Install the rechargeable battery pack in the handset
Insert the battery connector as shown in the diagram. Place the battery pack in the battery compartment and insert the battery cable in the clip provided. Put the battery compartment cover back into place and click shut.
To open the battery cover. Push tab downwards and pull. The cover clicks off.
4Charge the handset batteries for at least 16 hours
Place the handset on the base and charge for at least 16 hours without interruption.
Note
Under ideal conditions, the handset should give about 10 hours talktime or 100 hours standby on a single charge. However, new NiCad batteries do not reach their full capacity until they have been in normal use for several days.
Please note that the lifespan of NiCad rechargeable batteries depends on how heavily they are used. However, over time, their capacity to recharge will begin to diminish and they will eventually need replacing.
5Connect the telephone line cord to the base station
Ensure that this is fitted correctly into the right socket. (See the diagram on page 3).
6Plug your Verve 100 into the phone socket
7Register your handset to the base
You must register your handset to the
Using your Verve 100
To make an external call
Enter the telephone number, check that it is correct, and then press the HANDSET button to dial.
You will hear the number dialling and the 
icon will appear on the display.
Or
Press the HANDSET button. You will hear the dial tone.
Dial the telephone number you require. The number is dialled and will be shown on the display.
To end a call
Press the HANDSET button. The 
icon will disappear from the display.
Or
Place the handset back on the base station.
To receive an external call
Handset display symbols
Registered and ready for use.
Flashes if you go out of range of the base station or are not registered to the base station.
In use.
Save.
– ✱ character.
–
P
# button.
Handset ready for registration.
Recall button.
Searching for registered base.
Pause.
Handset located base, ready for registration.
Memory empty.
Do not stand your product on carpets or other surfaces which generate fibres, or place it in locations preventing free flow of air over its surfaces.
Do not submerge any part of your product in water and do not use it in damp or humid conditions, such as bathrooms.
Do not expose your product to fire, explosive or other hazardous conditions.
There is a slight chance that your phone could be damaged by an electrical storm. We recommend that you unplug the power and telephone line cord for the duration of the storm.
Cleaning
Simply clean the handset and base station with a damp (not wet) cloth, or an antistatic wipe. Never use household polish as this will damage the product. Never use a dry cloth as this may cause a static shock.
WARNING
Do not connect the telephone line cord to the phone socket until the handset is fully charged. This will prevent the risk of the phone being answered before the battery is charged.
Battery performance
After charging your Verve 100 for the first time, subsequent charging time is approximately
! base before you can make any calls. !
Unplug the power adaptor. Ensure that the handset is on the base. The 
icon will flash on the display. Plug the power adaptor back into the mains power socket. After approximately 90 seconds the 
icon will stop flashing.
The handset is now registered.
Please remove the protective film from the display on the handset.
Note
If you experience any difficulties setting up or using your phone, call the BT Helpline on 08457 908070.
When the phone rings, pick up the handset, press the HANDSET button and speak.
To redial the last number
Press the REDIAL button. The display will show the last number dialled.
Press the HANDSET button. The number is dialled.
1 | 2 | 3 | 4 | 5 | 6 |