Sanyo CLT-2423 Changing the Battery, Recycling NICKEL-METAL Hydride Batteries, Power Failure

Page 15

CLT-2419-2423E-NEW 3/14/03 3:32 PM Page 28

CHANGING THE BATTERY

Battery replacement and handling

When the operating time becomes short even after a battery is recharged, please replace the battery.

With normal usage, your battery should last about one year.

For a replacement battery, please contact your place of purchase or fill out and mail the enclosed Battery Order form.

Caution:

•Use only the specified battery type (3.6 V, 600 mAh).

•Do not remove the battery from the handset to charge it.

•Never throw the battery into a fire, disassemble it, or heat it.

•Do not remove or damage the battery casing.

•Remove battery if storing the phone over 30 days.

Make sure the telephone is off before you replace

 

the battery.

1

1. Slide off the battery compartment cover.

 

2. Disconnect the battery plug from the jack in the compartment and remove the battery pack.

3.Insert the new battery pack and connect

the cord into the jack.

4.Put the battery compartment cover back on.

5.Place handset on the base to charge for 12 hours.

Note: If the handset battery is removed for more than 5 minutes, the directory memory and Caller ID memory will be erased.

Charge the handset battery for 12 continuous hours prior to first use. The initial battery charge is important for best performance.

Caution: To reduce the risk of fire or personal injury, use a 3.6 V,

600 mAh battery. Replacement part number: GES-3AHRAAAU.

RECYCLING NICKEL-METAL HYDRIDE BATTERIES

NICKEL-METAL HYDRIDE BATTERIES MUST BE

DISPOSED OF PROPERLY.

Please take your used battery pack to a store that recycles Ni-MH batteries.

POWER FAILURE

During the period that the power is off, you will not be able to make or receive calls with the telephone.

After a power outage, place the handset in the base for about 20 seconds to reset the digital security code.

HEADSET JACK AND BELT CLIP

Headset connection (Headset not included)

For hands free conversation, connect the headset (not included) to the HEADSET jack. The handset earpiece and microphone are disabled when the headset is connected.

• Press TALK to answer or place a call while using the headset.

Belt clip installation

• Attach the belt clip by inserting the sides of the belt clip into the slots.

•Snap the ends of the belt clip into place.

28

29

Page 14 Page 16
Image 15
Page 14 Page 16
Contents CLT-2419 CLT-2423 Table of Contents Getting Started IntroductionMounting on a wall Battery setupTone/pulse setting Telephone line connectionNames and Controls HandsetBase unit Initial Programming On the baseOn the handset Using handset Using base speakerphoneBasics Base ringer Speakerphone volumeHandset volume Handset ringerFrom the base From the handsetConferencing from the handset From the handset in Talk modeFrom the base in speakerphone mode Conferencing from the baseChan Channel key Cancel keyLow battery warning Voice MAIL/IN USE indicatorReviewing Caller ID list Caller ID FeaturesCaller ID with Call Waiting Caller ID listStoring a name/number in the directory DirectoryDialing a Caller ID number Deleting entries from the Caller ID listChanging a stored number Reviewing and deleting directory contentsInserting a pause in the dialing sequence Replacing a directory entry with a Caller ID entryHeadset Jack and Belt Clip Changing the BatteryPower Failure Recycling NICKEL-METAL Hydride BatteriesSound Signals TroubleshootingLCD Screen Messages Causes of poor reception MaintenanceCharge it for a full 12 hours Maximize Battery PerformanceRefresh battery Keep the contacts cleanOriginal Retail PURCHASER’S Responsibility Technical Information Sanyo Comfort WarrantyBetween 830 am 700 pm EST SOS Help Line
Top Page Image Contents