VTech i 5803 operating instructions Important Safety Instructions

Page 1

Important Safety Instructions

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:

1.Read and understand all instructions.

2.Follow all warnings and instructions marked on the product.

3.Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

4.Do not use this product near water (for example, near a bath tub, sink or swimming pool).

5.Do not place this product on an unstable surface such as a table, shelf, or stand. The product may fall, causing serious damage.

6.Slots and openings in the back or bottom of the Base Unit and Handset are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. This product should not be placed in any area where proper ventilation is not provided.

7.This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local power company.

8.Do not allow anything to rest on the power cord. Do not install this product where the cord may have anyone walking on it.

9.Never push objects of any kind into this product through slots in the Base or Handset as they may touch dangerous voltage points or short out parts that could result in

a risk of fire or electric shock. Never spill liquid of any kind on the product.

10.To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the Base or Handset other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used.

11.Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.

12.Unplug this product from the wall outlet and refer servicing to an authorized service facility under the following conditions:

A. When the power supply cord or plug is damaged or frayed.

B.If liquid has been spilled onto the product.

C.If the product has been exposed to rain or water.

D.If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as improper adjustment of other controls may result in damage and often requires extensive work by an authorized technician to restore the product to normal operation.

E.If the product has been dropped and the Base and/or Handset has been damaged.

F.If the product exhibits a distinct change in performance.

1

Page 1 Page 2
Image 1
Page 1 Page 2
Contents Important Safety Instructions Important Safety Instructions Introduction Image Editor Software CD- Rom Parts Check ListHandset Layout Base Unit Layout Started SetupCharging of the Handset Battery Cells Installation and Charge of Battery Cells in HandsetFollow these steps Checking for Dial Tone Connecting to Phone LineTone/Pulse Selection DifficultyInstallation Power Guard/Spare Battery Charger FeaturePower Guard Installation and Registration of Accessory Handset Setup Of The i 5803/i 5807 Acces- sory Handset Installation and Registration of Accessory HandsetRegister Additional i5803/i5807 Handsets RegistrationIcon Handset and Base IndicatorsBase Unit Icons Handset LEDsBase LEDs DescriptionNavigation Key NavKey Handset MenuMenu Shortcuts Main MenuIntercom Screen SaverGlobal Page from Handset From Handset to BaseAdding Phonebook Entries PhonebookDefault None Editing Phonebook EntriesSearching for and Dialing Phonebook Entries Deleting Phonebook Entries Review CID Log Clear CID Log Review Redial Calls LogClear Redial Sounds & Alerts SettingsBlue Green Tan Rose Images Emotions My Picture CD ROM PicturesSet a Wallpaper Image Clear a Wallpaper ImageRecord a Ringer Recordable RingerPicture Download One-Time Software InstallationDownload Your Own Image Image DownloadPicture Download Redial Base Menu Soft FunctionsErasing Numbers in Redial Memory Saving Redial Numbers in Phonebook MemoryCalls LOG Caller ID Base Unit MenuDialing from Caller ID Reviewing Caller ID from the BaseCaller ID Call Waiting ID Deleting CID Records Save CID Records to Phonebook MemoryRinger Volume Base SettingsRinger Melody Tone/Pulse preset to Tone Keypad Tone preset to onLanguage preset to English ContrastPhonebook Memory To Store a Number/NameSave To Search For and Dial a Number/ NameTo Edit a Number To Delete a Number/NameBase Menu Soft Functions Making Calls Handset and Base OperationAnswering Calls Press SpeakerphoneBase Speakerphone Volume Handset VolumeSound Select Handset Only Flash Function Hold FunctionFrom the Handset From the BaseBase Speakerphone Operation Handset Speakerphone OperationLine in Use Indication Transferring Calls Conference CallingBlind Transfer Announced TransferHeadset Operation To purchase a Headset, call VTech Customer Service atBelt Clip Maintenance Case Of Difficulty Handset does not ring when you receive a callPhone doesnt work at all No dial toneYou hear other calls while using your phone Your Handset vibrates or shakes when a call comesCommon cure for electronic equipment What does this limited warranty cover? Warranty StatementHow long is the limited warranty period? What is not covered by this limited warranty?Other Limitations How do you get warranty service?FCC Part FCC, Acta and IC RegulationsFCC and Acta Information Product identifier and REN information Programming/testing of emergency numbersConnection and use with the nationwide telephone network Repair instructionsIC Industry Canada Nominal Effective Range Technical SpecificationsTable Of Contents Headset Operation Handset and Base OperationIndex Connecting Power toIssue
Top Page Image Contents