VTech VT 1930c manual Quick Reference Guide, Int.Co, Storing Memory Speed Dial Numbers

Page 21

QUICK REFERENCE GUIDE

Set-Up Adapter

¥Plug AC adapter into a standard electrical outlet and Base Unit.

¥Set TONE/PULSE switch to PULSE or TONE. The unit is factory set to TONE.

¥Let the handset battery pack charge for 16 hours before first use.

¥Connect telephone line cord to base unit and telephone jack.

Making Calls

¥Press the PHONE key. When HANDSET ONis displayed and you hear a dial tone, dial the number.

OR

¥Enter the number to be dialed on the display and then press the PHONE key.

OR

¥Press SPKP on the Base Unit, then dial the number.

Answering Calls

¥To answer a call, press any key other than OFF , MUTE , or the Volume Keys. The handset will NOT auto-answer when lifted off the base cradle.

OR

.

Press SPKP on the Base Unit.

Hanging Up

¥ Press OFF or place the handset in the cradle to hang up a call.

To Place A Call On Hold

¥ Press HOLD on the Handset or Base Unit to place an active call on HOLD.

. To return to the call on the Hand- set, press either PHONE or HOLD .

. To return to the call on the speakerphone, press either HOLD or SPKP .

To Mute A Call

¥Press MUTE to disable the Handset or Base Unit microphone.

¥ Press MUTE again to return to normal two way conversation.

To Page The Handset

¥To page from the base, press

INT.CO .

¥To cancel the PAGE either press INT.CO again on the base or press OFF on the handset.

STORING MEMORY (SPEED) DIAL NUMBERS:

¥The phone should be OFF .

¥Enter the number you wish to store on the display up to a maximum of 20 digits.

FLASH

		PAUSE
	PHONE	HOLD	OFF
		HOLD		STORING SPEED DIAL
				STORING SPEED DIAL
	1	2	3	NUMBERS
		abc
	4	5	6	DIAL YOUR PHONE
	ghi	jkl	mno	DIAL YOUR PHONE
	7	8	9	NUMBER
	7	8	9
	pqrs	tuv	wxyz	PRESS MEM/PGM
	*	0	#	PRESS MEM/PGM
	*	0	#
	tone	oper		PRESS LOCATION
	MEM/PGM	CID	REDIAL	PRESS LOCATION
	INT.COM	CLR/DEL	MUTE	(00..20)

21

Image 21

Contents Introduction Special Features Wall Mounting Parts Check ListFCC Part FCC and IC RegulationsFCC and IC Regulations FCC and IC Regulations Read and understand all instructions Important Safety InstructionsImportant Safety Instructions To Charge The Battery Pack Replacing the Battery PackIts Impossible To Overcharge The Battery Pack Word About Rechargeable Batter- iesDownward To Replace The Handset Battery Pack Follow The Steps BelowInstallation Spare Battery ChargerPower Backup Replacing a Drained Handset batteryHandset Ringer Getting StartedFill in the telephone number card on the base unit Wall Mounting Handset Display Messages Examples of the Handset DisplayLCD DISPLAY-EXAMPLES Base Unit Function Keys Handset Layout Base Unit Layout Base Unit Features Quick Reference Guide INT.COStoring Memory Speed Dial Numbers From the Handset Memory Dialing speed Dialing¥ Press MEM/PROG From the Base Unit Press the Speaker Phone keyUsing Redial From the Handset From the Base UnitRedial Hold Flash Basic OperationRedial MuteBasic Operation Advanced Functions Switching calls using FlashCall Waiting Message WaitingTemporary Tone Programming The RingerChanging Ringer Types Advanced Functions Clear/Delete CLR/DEL Key Advanced DialingMulti Level Redial Memory Dialing Storing Memory Speed Dial numbersDialing From Memory From the Handset Deleting Stored Numbers Changing Stored NumbersDeleted Storing Special CodesCaller ID CID Receiving and Storing CallsDialing From Caller ID CID Memory Transmission Error Special Message Indicators Out of Area CallsÒPrivateÓ Calls PrivateReviewing Number Reviewing NumbersDeleting Numbers Noise Or Interference Additional Operating TipsAutomatic Security Coding Out Of Range indicationCleaning your telephone MaintenanceAvoid water Electrical stormsYOU Hear Other Calls While Using Your Phone Handset does not Ring When YOU Receive a CallCase of Difficulty Phone Doesnõt Work AT ALLCommon Cure for Electronic Equipment Warranty Statement Technical Specifications Table of Contents Issue