VTech VT 1980, VT-1981 manual FCC Part, Vtech Communications AT, Vtech Electronics AT Canada

Page 18

This equipment complies with Part 15 and 68 of the Federal Communications Commission (FCC) rules for the United States.lt also complies with rules RSS-210 and CS-03 of Industry Canada (IC) for Canada.

A label is located on the underside of the base unit c o n t a i n i n g e i t h e r t h e FCC registration number and Ringer Equivalence Number (REN) or the IC registration number .You must, upon request, provide this informationto your local telephone company.

This equipment is compatible with inductively coupled hearing aids.

Should you experience trouble with this telephone equipment, please contact:

VTECH COMMUNICATIONS AT

1-800-595-9511 in the US

and VTECH ELECTRONICS AT

1-800-267-7377 in Canada.

for repair / warranty information. The telephone company may ask you to disconnect this equipment from the line network until the problem has been corrected.

Your V T 1980 / VT 1981 is designed t o operate at the maximum power allowed by the FCC and IC. This means your handset and base unit can

communicate only over a certain distance -which will depend on the location of the base unit and handset and layout of your home or office.

FCC PART 15

The equipment has been tested and found to comply with part 15 of the FCC rules. These limits are designed to provide reasonable p r o t e c t i o n against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in particular installation. If this equipment does cause harmful interference to radio or television reception, which can be d e t e r m i n e d b y t u r n i n g the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet or on a circuit different from that to which the receiver is connected.

-Consult the dealer or an e x p e r i e n c e d r a d i o / T V technician for help.

FCC PART 68

The FCC requires that you connect your cordless telephone to the nationwide telephone network through a modular telephone jack (USOC, RJ11C or RJl 1W)

Your telephone company may discontinue your service if your equipment causes harm to the telephone network.They will notify you in advance of disconnection, if possible. During notification, you will be informed of your right to file a complaint with the FCC.

Occasionally your telephone company may make changes in its facilities, equipment, operation, or procedures that could affect the operation of your equipment. If so, you will be given advance notice of the change to give you an o p p o r t u n i t y t o m a i n t a i n uninterrupted service.

The base unit contains no user serviceable parts. The handset contains a user replaceable battery pack.

If it is determined that your telephoneequipmentis malfunctioning, the FCC requiresthat it not be used and that it be unplugged from the modular jack until the problem has been corrected. Repairs to this telephone equipment can only be made by the manufacturer or its authorized agents or by others who may be authorized by the FCC. For repair procedures, follow the instructions outlined under the VTECH Limited Warranty.

This equipment may not be used on coin service provided by the phone company or Party lines.

The REN is useful in determining the number of devices you may connect to your telephone line and still enable the devices to ring when you receive a call.The general rule is that the REN value should not exceed 5.OA total; however, contact your local telephone company for the specific number in your area.

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model VT 1980/ VT.1981 Table of Contents Temporary Tone Other Special Features areTo Preset the Ringer Volume To PUT a Call on HoldParts Check List Install the Battery Pack Charging the Handset BatteriesIf the Batteries Dontrecharge Setting UP Your VT 1980 1 VT Use only Vtech batteryCheck for a Dial Tone TT. If you have rotary service, set the switch to DP Positionthe Wall Mount Adaptor on the BaseUsed to switch to Temporary Completed Tone dialing mode Used to increase the ringer volume during OFF modeVolume during a call Last number that was calledTemporary Tone DisconnectingMaking Calls Answering CallsTo Programming Speed DlAL Numbers Memory Dialing Speed DialingSpeed Number Dialing To Change or Replace a Speed DlALUsing Redial Storing Pauses in MemoryTo PUT a Call on Hold Mute Feature Volume ControlTo Preset the Ringer Volume Installation OperationProblemRemedy Problem Remedy ProblemWhat does OUR Warranty not Cover ? What does OUR Warranty Cover ?HOW do I Send MY UNIT, in or OUT of Warranty ? For HOW Long After the Original Purchase ?FCC Part Vtech Communications ATVtech Electronics AT Canada Frequency Control WeightPower Requirements Transmit Frequency

VT 1980, VT-1981 specifications

The VTech VT-1980 and VT-1981 are significant entries in the realm of educational toys, part of VTech's pioneering series of early learning devices aimed at nurturing young minds through interactive play. Launched in the early 1980s, these models stand out for their innovative use of technology and their engaging user experience.

The VT-1980, in particular, showcased a combination of fun and educational content designed to assist children in their early developmental stages. With a vibrant, colorful design that appealed to children, it featured a straightforward interface, ensuring that users could navigate the device without frustration. The device primarily functioned as an interactive learning tool, encouraging kids to engage with letters, numbers, and basic words.

One of the notable features of the VT-1980 was its multiple game modes, which provided an entertaining way to learn foundational skills. This included word recognition and simple math exercises, allowing children to practice through play. Its audio capabilities were also a highlight, with pleasant sound effects and encouraging voice prompts that motivated children to continue exploring.

Transitioning to the VT-1981, VTech made several enhancements upon its predecessor. The VT-1981 introduced more advanced learning modules, featuring an expanded library of games and activities that covered a broader range of educational topics. This model emphasized interactivity even further, incorporating touch-sensitive keys that responded to children’s inputs more effectively, enhancing their engagement with the device.

Both models utilized durable construction, ensuring the toys could withstand the rigors of play while remaining safe for young users. The technology was designed with longevity in mind, engaging children not just once but encouraging repeated use and continued learning over time.

Furthermore, VTech's commitment to providing educational content resonated across both models. They took significant steps to ensure that parents could trust the devices to offer quality learning experiences, highlighting the brand’s dedication to early childhood education.

In conclusion, the VTech VT-1980 and VT-1981 are exemplary representations of how technology can merge with play to create enriching educational experiences for young children. Their innovative features, combined with VTech's relentless pursuit of educational value, solidified their position as beloved tools in early learning, marking an important chapter in the evolution of educational toys.
Top Page Image Contents