I N S T A L L A T I O N
Power cord | Channel on base |
Push in on the two tabs at | Wrap any excess line cord |
|
|
|
|
|
|
|
|
| Guide the power cord |
|
|
| ||||||||||||||||||||||||||||||||
| the large end of the | around the 4 tabs on the |
|
|
|
|
|
| from the jack through the |
|
|
| ||||||||||||||||||||||||||||||||||
| triangular mounting | underside of the phone base. |
|
|
|
|
|
|
|
|
|
| channel on the base. |
|
|
| ||||||||||||||||||||||||||||||
|
|
|
|
|
|
| bracket. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Turn the mounting | Feed the free end of the | Slide the base down | |
line cord through the | |||
bracket so the double | onto the knobs until it | ||
rectangular opening in the | |||
slot is at the bottom. | locks in place. | ||
center of the bracket. | |||
|
|
FOR WALL INSTALLATION
The wall mounting bracket is a wedged, triangular plastic piece attached to the bottom of the base. You'll need to attach this piece so the thickest end of the bracket is facing the floor when you
1Remove the mounting bracket.
Push in on the two tabs at the large end of the triangular mounting bracket. (The tabs are marked "PULL TAB TO RELEASE.") Lift the bracket off the unit.
2Follow Steps 1, 2, and 3 in FOR TABLE/DESK INSTALLATION.
3Reverse the handset tab.
Pull the tab on the base up and away from the base. Turn the tab around, and slide it back into the opening. The notch should be facing up to hold the handset when you place it in the base.
4Connect the telephone line cord.
Plug one end of the line cord into the jack on the base. Guide the cord from the jack through the curved channel on the bottom of the base. Wrap any excess line cord around the 4 tabs on the underside of the phone base. (Make sure you leave enough cord free to extend to the wall jack.)
5Connect the power cord to the base.
Plug the power cord into the jack labeled DC12V on the back of the base.
6Guide the power cord from the jack through the channel on the base, as shown in the illustration above.
7Turn the mounting bracket so the double slot is at the bottom. Feed the free end of the line cord through the rectangular opening in the center of the bracket.
8Connect the line cord to the wall jack. Make sure it snaps firmly in place.
9Mount the base on the wall.
Hold the base so the mounting knobs on the wall plate fit the keyhole slots on the base. Slide the base down onto the knobs until it locks in place.
10Plug the AC adapter on the power cord into an electrical outlet.
11Follow Steps 6, 7, and 8 in FOR TABLE/DESK INSTALLATION.
2