AT&T 7610 user manual Lift panel door, To access features, Charge the handset batteries before use

Page 3

I N S T A L L A T I O N

Base Antenna (extended)

CHARGING

 

 

 

 

 

 

 

HANDSET

IN

USE

MEMO/REWIND

 

 

 

 

 

 

 

 

 

 

 

 

 

CLOCK

Lift panel door

 

 

 

 

FAST

 

 

 

 

 

 

 

FWD

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SAVE

 

 

to access features

 

 

 

 

 

 

 

PLAY/STOP

 

 

 

 

 

 

 

 

 

(see figure at right).

 

 

 

 

 

 

 

 

 

Cover

Turn system on or off.

Record or play outgoing announcement.

Fast forward during message playback.

VOLUME

Audible clock; also use with

CHANGE to set time/day.

 

 

Adjust message playback volume.

Play messages or

stop message playback.

Save messages.

Use with other buttons to change settings.

should be on steadily. If the light is flashing rapidly, the microcassette is not installed properly. Remove the cassette, and check to see if it's damaged. If it's okay, install it again. After you have installed the cassette, press Pto reset the system.

CAUTION: Use only the power supply provided with this

product. To obtain a replacement, call

1 800 722–9125. Power Supply DAS-2. Input: 120V, 60Hz, 15W. Output: 9V AC, 780 mA.

8Charge the handset batteries before use.

Place the handset face down in the base. The CHARGING light on the base goes on to show the handset is in the right position to charge the batteries. The batteries will be fully charged in 14 hours.

9Check for dial tone.

Make sure the base antenna is upright. After the batteries are charged, pick up the handset and check for dial tone by pressing P; the PHONE light should go on and you should hear a dial tone. Press Pto hang up.

10Set the dial mode.

If you have touch tone service, the phone will be ready to use as soon as the battery is charged.

If you have dial pulse service, you’ll need to set the dial mode. Press P(wait for dial tone), p,

#, #, #, 3. To return to touch tone dialing with touch tone service, when the phone is off, press P (wait for dial tone), p, #,

#, #, 8.

IMPORTANT: After you have installed the phone, you will need to record an announcement that callers will hear when the system answers. Please see the Answering System Operation section of this manual.

2

Image 3
Contents Part Mount the base on the wall InstallationSet the Handset Ringer ON/OFF switch Connect the power cordCharge the handset batteries before use To access featuresSet the dial mode Lift panel doorT T E R I E S Charging Handset Battery PackIf the phone does not work at all, check these items first If you hear noise or interference when using the phoneIf the phone does not ring when you receive a call C a S E O F D I F F I C U L T YIf the system does not respond to remote commands If you have difficulty hearing messagesIf the recording tape sticks or malfunctions E R a T I O N M O R Y E R a T I N G R a N G E Changing ChannelsIf you receive a call while you are out Recording Your Announcement Volume ControlSetting the Clock S W E R I N G S Y S T E M O P E R a T I O NBypassing Announcement When the Tape is FullRing Select Answering CallsTurning System On Remote Access CodeChanging Your Remote Access Code Recording a New AnnouncementOperation From a Remote Touch Tone Phone Answering SystemCommand