Telex BTR-24 manual System Operation, TR-24 Beltpack on Hip

Page 12

2.Plug the master TR-24’s external power supply into an AC outlet if desired. If external power is not desired then run off internal battery.

3.Place the TR-24’s in a location where it will have the best visibility to the other TR-24s.

4.Plug a headset into the master TR-24 beltpack.

5.Power-up the master TR-24 beltpack in master wireless mode. The master wireless mode is entered by holding the <1> button down as the unit boots. Once a beltpack was booted in a mode (wireless, wired, master wireless), the beltpack will always boot in that mode until the user sets a different boot mode.

•The power light should immediately light solid.

•After 20 seconds a beltpack voice prompt will announce “master wireless” in the headphone.

•Audio channel one’s light will activate indicating communication has started.

6.Plug headsets into TR-24 beltpacks.

7.When the master TR-24 has finished booting, power-up the TR-24 beltpacks in wireless mode. The wireless mode is entered by holding the <TALK> button down as the unit boots. Once a beltpack was booted in a mode (wireless, wired, master wireless), the beltpack will always boot in that mode until the user sets a different boot mode.

•The power light should immediately light solid.

•After 20 seconds a beltpack voice prompt will announce “wireless” in the headphone.

•Audio channel one’s light will activate indicating communication has started.

System Operation

By following the previous setup instruction, the system should now be up and running. Please read the following information for optimization / best performance of that system.

Beltpack position - When operating the system, wear the beltpack on the hip. Place it in a position that allows for greatest visibility to the master TR-24 antennas. The internal antennas for the TR-24 are on the sides of the beltpack case. For best visibility of antennas, do not place other objects within 6 inches (15cm) of the beltpack on the belt.

Figure 5-10

TR-24 Beltpack on Hip

Beltpack Audio Channels -Press the <1> button for audio channel one only. Press the <2> for audio channel two only. Press both <1> and <2> buttons simultaneous to select both. Use the talk button to select between enabling / disabling the headset microphone path. The channel light(s) will blink if the microphone path is disabled. The light(s) will be solid if the microphone path is enabled. See table below for talk modes:

<TALK> Mode

Description

Activation

 

 

 

 

 

 

Push-to-Latch/

Microphone

 

is

Tap

<TALK>

Momentary

enabled

until

the

button. Tap again

 

button

is

tapped

to turn off.

 

 

again.

 

 

 

 

 

 

(default mode)

If held down for 1/2

<TALK>

held

 

second

 

 

the

down for over 1/2

 

microphone path is

second.

 

 

 

disabled on release.

 

 

 

Momentary Only

<TALK>

button

Press

<1>

+

(Push-to-TX)

enables

the

audio

<TALK> + <2>

 

path for only as long

until

voice

 

as it is held down.

prompt

indicates

 

The beltpack will be

momentary mode

 

in this

mode

until

(about

 

3

 

reset

 

 

to

seconds).

Do

 

push-to-latch mode.

again to go back

 

 

 

 

 

to push-to-latch

 

 

 

 

 

mode.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OFF 1

MIC

S.T.

2

 

ADJ

ADJ

 

Figure 5-11

Top View of TR-24

5-6

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Operating Manual Table of Contents System Features IntroductionGeneral Description Battery Indication BTR-24 Base StationControls and Connections Front ViewTR-24 Beltpack Top View Bottom ViewBeltpack Button Combinations All have voice prompts Specifications System Technical SpecificationsWireless Mode Ten Beltpacks in Wireless ModeOperation DescriptionSystem Operation Set-upFront and Rear of BTR-24 Wired Mode Talk Mode Description ActivationTop View of TR-24 Ten TR-24s communicating via Ethernet BackboneFive Wired TR-24s communicating with 5 wireless Set-upMaster Wireless Mode TR-24/BTR-24 Wired Data PacketsNetwork Requirements Description IP Type Destination IP ProtocalSystem Operation TR-24 Beltpack on HipBattery Charging Instructions Tour Group ExampleEncryption Code and Password Login PasswordEncryption Code Software VersionUser Menu Options Users Menu ScreenBattery Care/Long Term Storage Battery CareLong Term Storage Li-Ion BatteriesProblems Possible Cause Solution SectionTroubleshooting Problem Possible Cause SolutionRF Channels RF ChannelsRegulatory Information Regulatory InformationModel Number Part Number Description Accessories and Replacement Items BTR-24SYS-243 Bosch Communications Systems
Related manuals
Manual 2 pages 18.84 Kb

BTR-24, TR-24 specifications

The Telex TR-24 and BTR-24 are prominent products in the realm of wireless intercom systems, widely used in various applications including broadcasting, theater, and event production. These devices exemplify reliable communication technology, joining the ranks of professionals seeking seamless interaction in dynamic environments.

The Telex TR-24 is a beltpack transceiver designed for ease of use and flexibility. One of its key features is its lightweight and ergonomic design, allowing users to wear it comfortably for extended periods. The device boasts a high-quality audio performance with adjustable audio levels, providing clarity and reliability in communication. Its built-in microphone allows hands-free operation, which is essential in fast-paced workflow scenarios. Additionally, the TR-24 utilizes advanced digital technology to reduce noise and enhance voice intelligibility, ensuring users can communicate effectively even in noisy settings.

On the other hand, the Telex BTR-24 is a four-channel wireless base station that serves as the heart of the intercom system. Its ability to handle multiple channels simultaneously allows for better management of communication among team members. The BTR-24 is marked by its sophisticated frequency agility, which automatically selects the clearest channel to avoid interference. This feature is critical in ensuring uninterrupted communication in environments filled with various wireless signals.

The technology behind the TR-24 and BTR-24 utilizes cutting-edge digital transmission, significantly minimizing latency and maximizing range. This results in a robust communication link over various distances, making it suitable for larger events or expansive production sets. Both devices feature rechargeable batteries and a user-friendly interface, perfect for quick setup and operation.

Further enhancing their functionality, the TR-24 and BTR-24 can be easily integrated with other audio systems, making them versatile tools in diverse networking situations. They also include options for operating in various power modes, providing flexibility depending on the demands of the specific application.

Overall, the Telex TR-24 and BTR-24 stand out for their user-centric approach, reliability, and advanced technological features. They are designed to meet the rigorous demands of professionals in the entertainment and communications industry. With their exceptional audio quality, robust performance, and seamless usability, these devices continue to be a preferred choice for anyone seeking to enhance their communication capabilities.
Top Page Image Contents