Unitech 38647G user manual Battery Notices, Battery charge notice

Page 4

About This Manual

CAUTION! Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous laser light. Use of optical instruments with the scanner will increase eye hazard. Optical instruments include binoculars, microscopes and magnifying glasses. However, this does not include eye glasses worn by the user.

Battery Notices

The PA600 is equipped with a Lithium-Ion Battery Pack and Backup Battery. Both bat- teries will discharge power if not frequently used.

Recharge the PA600 for at least 16 hours in order to fully charge the main battery and backup battery. Recharge the PA600 through either of the following:

1.Plug the USB Charging Cable to the PA600 and insert the AC Adapter into the USB Charging Cable’s power jack.

2.Place the PA600 into the Docking Station and plug the AC Adapter to the Dock- ing Station’s power jack.

The Backup Battery ensures data stored on SDRAM is safe for up to 2 hours, when the Main Battery disconnects from the P600. To prevent data loss, do not leave the PA600 uncharged without the Main Battery for an extended time period.

NOTE: Rechargeable batteries are advised to replace every year or when 500 charge/discharge cycles occur to guarantee optimal performance. It is normal that the battery balloons or expands beyond one year or the maximum of 500 cycles. Although it does not cause harm, it can not be used again and must be disposed of according to the location's safe bat- tery disposal procedures.

If the performance decrease of greater than 20% in a Lithium-Ion bat- tery, the battery is at the end of its life cycle. Do not continue to use, and ensure the battery is disposed of properly.

The length of time that a battery power lasts depends on the battery type and how the device is used. Conserve battery life through the following:

Avoid frequent full discharges because this places additional strain on the bat- tery. Several partial discharges with frequent recharges are better than a deep one. Recharging a partially charged lithium-Ion battery does not cause harm because there is no memory.

Keep the lithium-Ion battery cool. Avoid a hot car. For prolonged storage, keep the battery at a 40 percent charge level.

Do not leave the lithium-Ion battery discharged and unused for an extended period because the battery will wear out and the longevity of the battery will be at least shorter than half of the one with frequent recharges.

Battery charge notice

It is important to consider the environmental temperature whenever the Lithium-Ion Battery Pack is charged. Charging is most efficient at room temperature or in a slightly cooler environment. It is essential that batteries are charged within the temperature range of 50°F - 113°F (10°C to 45°C). Charging batteries outside of this specified tem- perature range could damage the batteries and shorten their charging life cycle.

iii

Image 4
Contents User’s Manual PA600 Rugged Enterprise PDA382647G Version Regulatory Compliance Statements About This ManualFCC Warning Statement Laser Information FCC Label StatementCanadian Compliance Statement European Conformity StatementBattery Notices Battery charge noticeWarranty Storage and safety noticeTable of Contents Advanced Settings System Specification Worldwide SupportGetting Connected Bar Code Scanner ProgramsGetting Started Introducing the PA600 MCAFeatures Package Contents Front View Tour of the PA600Component Description Back View Installing the Battery Getting StartedReplace the Battery Compartment Cover Charging the Battery Charging the Battery Using the USB CableCharging the Battery with the Docking Station Checking the Battery StatusLED Status MeaningConnecting the PA600 to a PC Powering On Turning PA600 on for the First TimeUsing the Stylus Tap Start → Settings → Control Panel Calibrating the PA600 ScreenPage Setting the Data and Time Set Date and TimeKeypads and Function Buttons Using the HardwareKey Main Function Secondary Function Using the Hardware Using the SD/MMC memory card Adjusting the Screen BrightnessInserting a Storage Card Using the Laser Scanner Removing a Storage Card→ Settings → Control Panel → double- tap Scanner Tap Tools → Enable ScanScan2Key Icon Using the Rfid HF Reader Tap Start → Programs → Rfidhf → RfidhfUsing the Hardware Getting Connected Installing Microsoft ActiveSyncEstablishing Device-PC Connection Getting Connected Page Connecting the Device to the Computer Page Connection Options Synchronizing with the ComputerUSB Connection Check Enable direct connections to the desktop computer Tap Start → Programs → CommunicationBluetooth Connection Page Getting Connected BTAciveSync Icon Wi-Fi Connection Page Synchronization Options Synchronizing InformationUse Microsoft ActiveSync to Exchange Files Page Bar Code Scanner Programs Scanner SettingScan2Key Bar Code Symbologies 1D Bar Code Bar Code Symbologies 2D Bar CodeAdvanced Settings Adjusting SettingsChecking Main and Backup Battery Status Tap Start → Settings → Control Panel → double-tapPowerExtending Battery Life Changing the Automatic Power SettingsAdjusting Backlight Setting Viewing Flash Memory Files Performing a hardware reset Performing a Warm BootPerforming a Cold Boot System Specification AppendixWorldwide Support Region Web site