|
|
|
|
|
|
|
|
|
| Version 2.0 | |
|
|
|
|
|
| OptimusPDA SP5700 Series User Manual | |||||
|
|
|
|
|
|
|
| ||||
Problem |
| Cause |
|
|
| Solution |
| ||||
|
|
|
| ||||||||
| Scan window is dirty |
| Clean scanner window with a soft, wet cloth. | ||||||||
| Object | moves | while | Fix the object while scanning. |
| ||||||
| scanning |
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| ||
| Scanning |
| application | is | Tap on Start, then Settings → Control Panel, | ||||||
|
| and select the System tab to verify whether the | |||||||||
Your PDA | improperly opened |
|
| ||||||||
|
| unit is loaded with a scanning application or not. | |||||||||
|
|
|
|
|
| ||||||
does not | Unreadable barcode |
| Scan engine cannot read damaged barcodes. | ||||||||
accept scan | Distance | PDA | and | the | Adjust | the distance | between | them at | |||
data input | |||||||||||
objec too far or too close | approximately 6 inches, and try again. |
| |||||||||
|
| ||||||||||
| PDA is not programmed | Check whether your PDA is programmed to read | |||||||||
| for the barcode |
|
|
| the type of barcode you are scanning. |
| |||||
|
|
|
|
|
|
| |||||
| Scanning |
| beam |
| not | Angle the barcode at 45 degrees or place scan | |||||
| aligned with a barcode |
| beam against a barcode to use direct rays. | ||||||||
| OptimusPDA |
| was |
|
|
|
| ||||
| removed from the cradle | Insert you PDA into the cradle again. |
| ||||||||
| during | communication |
| ||||||||
|
|
|
|
| |||||||
ActiveSync | process |
|
|
|
|
|
|
|
|
| |
Incorrect cable |
|
|
| Verify cable is correct and is properly connected. | |||||||
does not |
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
| ||
operate | ActiveSync | is | incorrectly | Install the ActiveSync program again. |
| ||||||
| installed or configured |
|
| ||||||||
|
|
|
|
|
| ||||||
| Connected | as | a | Guest, | Take the terminal out, then insert it | the cradle | |||||
| not by previously created | ||||||||||
| again and enter your name again. |
| |||||||||
| name |
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| ||
| Volume level is very low | Check | the volume slider | in Volume & Sounds | |||||||
Sound is not | (Tap on Start → Settings → Control Panel) to | ||||||||||
or turned off |
|
|
| ||||||||
audible |
|
|
| ensure the volume is at adequate level. |
| ||||||
|
|
|
|
|
|
| |||||
| Dust fills the speaker |
| Clean the speaker. |
|
| ||||||
Program | Characters | are | written | To recognize handwriting input, characters must | |||||||
incorrectly |
|
|
|
| be written carefully, in a certain way. |
| |||||
does not |
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
| ||
recognize | Character |
| strokes | are |
|
|
|
| |||
handwriting | written on the wrong part | Fix the letter recognizer. |
|
| |||||||
| of the LCD |
|
|
|
|
|
|
|
| ||
Table 1 Solving problems |
|
|
|
|
|
|
|
|
| ||
Copyright © 2007 | 29 March 2007 |
Metrologic, Inc. | 62 |