3 Special Features | 4 Things You Should Know |
3-A Handset Locator
You can locate the handset or page the handset user with beep tones from the base unit.
1.Press [HANDSET LOCATOR] on the base unit.
•The TALK indicator on the handset and the IN USE indicator on the base unit flash rapidly, and the handset beeps for 1 minute.
2.To stop paging, press [HANDSET LOCATOR] again or press [OFF] on the handset.
•You can also stop paging on the handset by pressing any button except [▼] or [▲].
3-B Temporary Tone Dialing
(For Rotary or Pulse Service Users)
Press [
] (TONE) before entering access numbers which require tone dialing.
•The dialing mode changes to tone. You can enter numbers to access an answering service, electronic banking service, etc. When you hang up, the dialing mode will return to pulse.
3-C For Call Waiting Service Users
Press [FLASH/CALL WAIT] if you hear a call waiting tone during a conversation.
•The first call is put on hold and you can answer the second call.
•To return to the first caller, press [FLASH/CALL WAIT] again.
•If this function does not operate properly, consult your telephone company for details.
3-D FLASH Button
Pressing [FLASH/CALL WAIT] allows you to use special features of your host PBX such as transferring an extension call, or accessing optional telephone services such as call waiting.
•Pressing [FLASH/CALL WAIT] cancels Temporary Tone Dialing mode.
3-E Re-registering the Handset
If an alarm tone sounds when you press [ 
],
•Have both the handset and base unit nearby during registration.
•Follow steps 1 and 2 listed below. You have about 1 minute to complete them.
1.Base unit: Press and hold [HANDSET LOCATOR].
•The CHARGE indicator flashes.
2.Handset: Press and hold [FLASH/CALL WAIT] until a beep sounds.
•The VOICE ENHANCER indicator flashes.
•When registration is complete, a beep sounds from the handset and the indicator lights go out.
•Wait for 20 seconds after registration is complete while the handset establishes communication with the base unit.
•If the handset beeps 3 times in step 2, an error occurred. Try again from step 1.
•You can stop registration by pressing [OFF] on the handset, and pressing [HANDSET LOCATOR] on the base unit.
4-A Battery
Recharge
When the RECHARGE indicator flashes or RECHARGEIndicator the handset beeps intermittently, place the
handset on the base unit for 6 hours to recharge the battery.
•The RECHARGE indicator will flash when the handset battery is charged less than 15 minutes and the handset is lifted off the base unit.
Battery replacement:
If you cleaned the charge contacts and fully charged the battery, but after a few telephone calls, the RECHARGE indicator flashes, the battery may need to be replaced. Please order a new Panasonic
A nickel metal hydride battery that is recyclable powers the product you have purchased. Please call
Battery information
After your Panasonic battery is fully charged, you can expect the following performance:
Operation | Operating time |
|
|
While in use (TALK) | Up to about 5 hours |
|
|
While not in use (Standby) | Up to about 11 days |
|
|
•A fully charged battery will give you up to 5 hours of continuous talk time, or keep your handset in Standby mode to receive incoming calls for up to 11 days (if no phone calls are made). Battery power is consumed whenever the handset is off of the base unit, even when the handset is not in use. The longer you leave the handset off of the base unit, the time you can actually talk on the handset will be shortened. Actual battery performance depends on a combination of how often the handset is in TALK mode and how often it is in Standby mode.
•If the battery is fully charged, you do not have to place the handset on the base unit until the RECHARGE indicator flashes. This will maximize the battery life.
•If you want to keep the battery fully charged at all times, place the handset on the base unit when the handset is not used. The battery cannot be overcharged.
•Clean the charge contacts of the handset and the base unit with a soft, dry cloth once a month. Clean more often if the unit is subject to grease, dust or high humidity. Otherwise the battery may not charge properly.
4-B Belt Clip
You can hang the handset on your belt or pocket using the included belt clip.
To attach the belt clip | To remove the belt clip |
For assistance, please call: