TG7200_7220E(e)_QG.fm Page 4 Tuesday, May 15, 2007 9:42 AM
Frequently asked questions
|
| Question | Cause & solution |
|
| |||||
|
| Why is w flashing? | LThe handset is too far from the base unit. Move |
|
| |||||
|
|
|
| closer. |
|
| ||||
|
|
|
| LThe base unit AC adaptor is not connected. |
|
| ||||
|
|
|
| Check the connections. |
|
| ||||
|
|
|
| LYou are using the handset or base unit in an area |
|
| ||||
|
|
|
| with high electrical interference. Place the |
|
| ||||
|
|
|
| handset and base unit away from interference |
|
| ||||
|
|
|
| sources, such as antennas and mobile phones. |
|
| ||||
|
|
|
| LThe handset is not registered to the base unit. |
|
| ||||
|
|
|
| Register it (page 6). |
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
| What should I do when the | LMake sure that the batteries are installed |
|
| |||||
|
| handset does not turn on? | correctly. |
|
| |||||
|
|
|
| LFully charge the batteries. |
|
| ||||
|
|
|
| LClean the charge contacts and charge again. |
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
| How long is the battery | LWhen you are using |
|
| |||||
|
| operating time? | (supplied batteries); |
|
| |||||
|
|
|
| In continuous use: 17 hours max. |
|
| ||||
|
|
|
| In continuous standby mode: 180 hours max. |
|
| ||||
|
|
|
| LIt is normal for batteries not to reach full capacity |
|
| ||||
|
|
|
| at the initial charge. Maximum battery |
|
| ||||
|
|
|
| performance is reached after a few complete |
|
| ||||
|
|
|
| cycles of charge/discharge (use). |
|
| ||||
|
|
|
| LActual battery performance depends on a |
|
| ||||
|
|
|
| combination of how often the handset is in use |
|
| ||||
|
|
|
| and how often it is not in use (standby). |
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
| Can I keep the handset on | LEven after the handset is fully charged, the |
|
| |||||
|
| the base unit or charger | handset can be left on the base unit or charger |
|
| |||||
|
| when I am not using it? | without any ill effect on the batteries. |
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
| When should I replace the | LIf the batteries are fully charged until 5is |
|
| |||||
|
| batteries? | displayed, but 7is displayed after a few calls, |
|
| |||||
|
|
|
| replace the batteries with new ones. |
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
| What is a PIN? | LThe PIN is a |
|
| |||||
|
|
|
| in order to change certain base unit settings. The |
|
| ||||
|
|
|
| default PIN is “0000”. |
|
| ||||
|
| What do I need to do to | LYou need to subscribe to Caller ID service. |
|
| |||||
|
| display caller information? | Consult your service provider/telephone company |
|
| |||||
|
|
|
| for details. |
|
| ||||
|
|
|
| LThe message “You must first subscribe |
|
| ||||
|
|
|
| to Caller ID.” will be displayed until you |
|
| ||||
|
|
|
| receive caller information after subscribing to |
|
| ||||
|
|
|
| Caller ID service. |
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| – 4 – |
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|