Cobra Electronics LI 5600DX owner manual VibrAlert and Call Alert, To change call settings

Page 14

10289_LI5600DX_PH2 8/10/07 11:28 AM Page 22

Mode Functions

Operation

During memory location scan (while receiving an Incoming transmission), you can choose from the following:

a. Press and hold the Talk button to communicate on that

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Introduction

Operation

Customer Assistance

Warranty

 

 

 

VibrAlert and Call Alert

•

Your microTALK radio can alert you to incoming signals by sounding an audible call tone, by vibrating silently or both.

memory location.

b. Your radio will remain on that memory location and return to Standby mode. Press the Channel Up or Channel Down button to resume scanning memory locations.

c. After 10 seconds of inactivity, unit starts scan again.

If you press the Talk button while scanning, but more than

10 seconds after receiving a transmission, you will transmit on the memory location on which, during scanning, you last received a transmission.

If you do not press any button within 10 seconds, your radio will automatically resume scanning memory locations.

Mode Button

Channel Buttons

To change call settings:

1.Press the Mode button until the Call Setting icon flashes on the display. The current setting (“01” vibrate + ring, “02” vibrate only or “03” ring only)

is displayed.

2.Press the Channel Up or Channel Down button to change the call setting.

3.Choose one of the following:

VibrAlert + Ring

VibrAlert Only

Ring Only

During memory location scan (while not receiving a transmission), you can choose from the following:

a. Press and hold the Talk button to communicate on the channel/privacy code that was displayed before you entered mode functions or memory location on which, during scanning, you last received a transmission.

b. Press the Mode button to proceed to other functions.

c. Press the Lock/Enter button to return to Standby mode on the channel/privacy code that was displayed before you entered mode functions or the memory location on which, during scanning, you last received a transmission.

To reduce the number of memory locations being scanned, you may de-program any unwanted locations. (See page 16 to de-program a memory location.)

a. Press the Mode button to enter the new setting and proceed to other functions.

b. Press the Lock/Enter button to enter the new setting and return to Standby mode.

 

 

 

 

22

Nothing Comes Close to a Cobra® 23

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Automated Help Desk Making Life Easier and SaferFor Assistance in the U.S.A Customer Assistance OperatorsFeatures Product FeaturesWarranty and Trademark Acknowledgement Trademark AcknowledgementEstimated operation time on full charge 10 hours Replace battery compartment cover and belt clipCaring for Your microTALK Radio Insert radios into desktop charger as shown Using Your RadioFor charging microTALK radios in desktop charger Plug 120-volt adapter into electrical outletCall Button ChannelsListening for a Response To Illuminate DisplayAuto Squelch/Maximum Range Lock FeatureSignal Strength Meter MicroTALK RangePrivacy Codes Mode FunctionsScrolling through Mode Functions Set DCS Privacy Codes Set Ctcss Privacy CodesTo select a Ctcss privacy code To select a DCS privacy codeMemory Locations To turn VOX mode on or offVoice Activated Transmit VOX To set VOX sensitivityTo recall a stored memory channel location Press the Mode button toChoose one of the following DisplayFlash on the display To de-program a memory locationChannel Scan ThroughPrivacy Code Scan Press the Mode button to proceed to set privacyPress the Channel Up or Channel Down button to Memory Location Scan To scan memory locationsTo change call settings VibrAlert and Call AlertKeystroke Tones Mode Functions General SpecificationsCall Tone Settings Roger Beep Confirmation ToneGeneral Specifications FCC License General SpecificationsProduct Service Product Service Questions
Top Page Image Contents