Cobra Electronics LI7200WX Using Your Radio, For charging microTALK radios in desktop charger

Page 4
1. Press and hold the Talk button.
2. With the microphone about 2 inches (5 cm) from your mouth, speak in a normal voice.
3. Release the Talk button when you are finished talking and listen for a response.
You cannot receive incoming calls while pressing the Talk button.
Both radios must be tuned to the same channel/privacy code to communicate.
Your microTALK® radio has a unique circuit designed to extend battery life. If there are
no transmissions for 10 seconds, the radio will automatically switch to Battery Save mode and the Power Saver icon will flash in the display.
This will not affect the radio’s ability to receive incoming transmissions.
Communicating with Another Person
Auto Battery Save
Turning on Your microTALK® Radio
Press and hold the Power button until you
hear a series of audible tones indicating the radio is on.
Your microTALK® radio is now in Standby mode, ready to receive transmissions. The radio is always in Standby mode, except when the Talk, Call, Mode or Power buttons are pressed.
Battery Low
•
When battery power is low, the Battery Low icon will blink. Your batteries should be recharged.
Customer Assistance Warranty
•
•
•

10293_LI7200WX_vB.qxd 9/5/07 10:55 AM Page 2

Introduction

Insert Radio(s)

Using Your Radio

For charging microTALK® radio(s) in desktop charger:

1.Insert radio(s) into desktop charger as shown.

2.Insert round connector of 120-volt adapter into jack on back of charger.

3.Plug 120-volt adapter into electrical outlet.

Introduction

Operation

On/Off Power

If charging light is not on, check position of radio. Radio should be upright. The charge indicator light will stay on as long as the radio is in the charging well.

It normally takes about 15 hours to fully recharge battery pack. Battery pack will not be damaged if they stay in the charging well longer than that.

To charge a single radio, you can bypass the desktop charger and simply insert the wall adapter’s round connector directly into the speaker/microphone/charge jack located on the top of the radio.

Use only the supplied rechargeable batteries and charger for recharging your Cobra microTALK® radio.

Cobra recommends your radio is turned off while being charged.

Quick Start

1. Press and hold the Power button to turn on your radio.

2.Press the Channel Up or Channel Down button to select a channel.

Both radios must be tuned to the same channel/privacy code to communicate.

3.Press and hold the Talk button while speaking into the microphone.

4.When finished talking, release the Talk button and listen for a response.

Battery Low

Battery Save Mode

Talk Button

Two Inches (5 cm) from Mouth

2

3

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Making Life Easier and Safer Product Features Warranty and Trademark AcknowledgementFeatures Trademark AcknowledgementAvoid exposure to extreme temperatures Replace battery compartment cover and belt clipCaring for Your microTALK Radio Estimated operation time on full charge 12 hoursUsing Your Radio For charging microTALK radios in desktop chargerInsert radios into desktop charger as shown Plug 120-volt adapter into electrical outletTo switch from high to medium to low power ChannelsListening for a Response Call Button To alert another person that you are callingLock Feature Signal Strength MeterAuto Squelch/Maximum Range MicroTALK RangeMode Functions Scrolling through Mode FunctionsPrivacy Codes Set Ctcss Privacy CodesStandby mode Set DCS Privacy CodesTo select a DCS privacy code NOAA* All Hazards Radio ChannelsVoice Activated Transmit VOX Memory LocationsPress the Mode button to Choose one of the followingTo recall a stored memory channel location While recalling a stored memory locationChannel Scan To de-program a memory locationTo scan channels Press the Mode button to proceed to set privacy Press the Channel Up or Channel Down button toPrivacy Code Scan Select Channel To scan privacy codesPress and hold the Talk button to communicate on Memory Location ScanTo scan memory locations To change call settings VibrAlert and Call AlertKeystroke Tones Call Tone SettingsRoger Beep Confirmation Tone General Specifications FCC License General SpecificationsProduct Service Product Service Questions
Top Page Image Contents