Cobra Electronics 29 WX ST Rear Panel, Operating Procedure to Receive CB Broadcasts

Page 7
RX/TX/WX LED INDICATOR. When your radio is in the CB receive mode, the LED will be green. When in transmit mode, the LED will be red and in Weatherband mode, the LED will be orange.
LED CHANNEL DISPLAY. The selected channel will be displayed. Display will be off when radio is in Weatherband mode.
16.
Operation (Cont.)
14. CH.19/CH.9/NORMAL SWITCH. Used for instant selection of emer- gency Channel 9 (CH. 9 position) or information Channel 19. In NOR- MAL position, all 40 CB channels are selected by the CHANNEL SELEC- TOR switch (9).
15. S-METER.Swings proportionally to the strength of the incoming signal during receiving. The S/RF-SWR-CAL switch must be in the S/RF position.
RF-METER.Swings proportionally to the RF output power while trans- mitting. The S/RF-SWR-CAL switch must be in the S/RF position.
SWR METER. Measures standing wave ratio of the antenna system. Used to properly adjust the length of the antenna and to monitor the quality of the coaxial cable and all RF electrical connections. If there is any degradation whatsoever in any of the foregoing, due to humidity, salt spray, vibration or corrosion, the SWR meter reading will rise, thereby indicating that a problem exists.
To calibrate, switch to the "CAL" position, transmit by pressing the mike switch, and adjust the SWR control to the "CAL" mark on the meter; then switch to "SWR" position for the SWR measurement.

17.

18. SOUNDTRACKER™ SWITCH. Depressing this button turns on the SoundTracker system in your CB.

19. SOUNDTRACKER™ INDICATOR. A red LED will illuminate when the SoundTracker system is engaged on your CB.

B. PRESS-TO-TALK MICROPHONE. Both the receiver and transmitter are controlled by the Press-to-Talk switch on the microphone. Press the switch and the transmitter is activated; release the switch to receive. When transmitting, hold the microphone two inches from the mouth and speak clearly in a nor- mal voice. The microphone provided with your radio is a detachable low- impedance dynamic type. The radio will not transmit in the Weatherband mode even though pressing the microphone switch will cause the red TX LED to illuminate.

10

Operation (Cont.)

3

1

2

4

C. Rear Panel

1. PUBLIC ADDRESS: An external 8-ohm 4.0 watt PA speaker may be connect- ed to the PA Speaker Jack when this unit is used as a public address system. The speaker should be directed away from the microphone to prevent acoustic feed-back. Physical separation or isolation of the microphone and speaker must be employed when operating the PA at high output levels.

2. EXTERNAL SPEAKER: The External Speaker Jack is used for remote receiver monitoring. The external speaker should have 8-ohm impedance and be rated to handle at least 4.0 watts. When the external speaker is plugged in, the inter- nal speaker is automatically disconnected.

3. ANTENNA CONNECTOR: This SO-239 connector permits connection of the transmission line cable PL-259 connector to the transceiver.

4. POWER. This jack permits connection of the DC power to the transceiver. A power cord with polarized plug is supplied with the radio. The polarized plug ensures that the power will always be connected properly.

Operating Procedure to Receive CB Broadcasts

1. Be sure that the power cord, antenna and microphone are connected to the proper connectors before proceeding further. The PA/CB should be in the CB position.

2. Turn the radio ON by rotating the VOLUME CONTROL clockwise.

3. Set the RF GAIN CONTROL fully clockwise.

4. Rotate SQUELCH CONTROL counterclockwise until incoming signal is heard.

5. Set the Channel Selector Switch to the desired channel.

6. Set VOLUME CONTROL to a comfortable listening level.

7. Engage the SoundTracker system by depressing the buttons labeled ST. SoundTracker system allows you to reduce unwanted background noise (stat- ic) and increase the signal for better reception.

Listen to the background noise from the speaker. Turn the SQUELCH CONTROL slowly clockwise until the noise JUST disappears (no signal should be present). Leave the control at this setting. The squelch is now properly adjusted. The receiv- er will remain quiet until a signal is actually received. Do not advance the control too far, or some of the weaker signals will not be heard.

11

Page 6 Page 8
Image 7
Page 6 Page 8
Contents WX ST Cuts Static coming in, adds Punch going out CB StoryNWR Frequencies and Transmission Characters Channel Channel Frequency MHz SpecificationsLocation InstallationMounting and Connection Base Station Operation Operation from 120VAC, House Current CB AntennaWX Antenna Ignition Noise InterferenceOperation Controls and IndicatorsFront Panel Rear Panel Operating Procedure to Receive CB BroadcastsHow SoundTracker Works Operating Procedure to TransmitCode Meaning Maintenance and AdjustmentAdjustment Warning AppendixFew Rules That Should Be Obeyed If You Think You Need ServiceHow Your CB Can Serve You Limited Two Year Warranty Warranty and Service

29 WX ST specifications

Cobra Electronics has long been a trusted name in the world of communication technologies, particularly in the realm of CB radios. One of its standout models, the Cobra 29 WX ST, exemplifies the brand’s commitment to quality and innovation. This classic 29-channel CB radio is designed for both professional and recreational users, providing reliable communication in various environments.

One of the most notable features of the Cobra 29 WX ST is its 40-channel capability, which ensures broader communication options. It also comes equipped with NOAA weather channels, allowing users to receive real-time weather updates and alerts. This feature is especially critical for those who use CB radios in outdoor settings, such as trucking and off-road driving, where weather conditions can rapidly change.

The Cobra 29 WX ST incorporates advanced sound technology, including a full-range speaker, which enhances audio clarity. The radio is designed to minimize noise interference, making it easier to hear incoming communications even in loud environments. The unit also features an easy-to-read display with a 4-color backlight for enhanced visibility, making it convenient to use at night or in low-light conditions.

For added versatility, the Cobra 29 WX ST includes a noise-canceling microphone that filters out background noise, allowing for clearer voice transmission. This technology is crucial for ensuring that communication is effective, especially in noisy surroundings such as highways or construction sites.

The radio also boasts a compact design, making it suitable for mounting in various vehicles without consuming excessive space. Its rugged construction ensures durability in demanding environments, further solidifying its suitability for professional use, including trucking and emergency services.

Additionally, the Cobra 29 WX ST supports PA capabilities, which can be particularly useful for emergency announcements or communicating with groups outside the vehicle. The unit features adjustable power settings, allowing users to choose between low and high power for optimized communication range.

Overall, the Cobra 29 WX ST is a feature-rich CB radio that balances durability, functionality, and advanced technology. Whether you are a long-haul trucker, a recreational off-roader, or someone in need of reliable communication, the Cobra 29 WX ST delivers performance that meets a wide range of needs. With its impressive set of features and user-friendly design, it remains a preferred choice for those seeking a dependable communication tool in any situation.
Top Page Image Contents