Cobra Electronics 150GTLDX owner manual Alternate Microphones and Installation

Page 13

Alternate Microphones and Installation

Alternate Microphones and Installation

Your Mobile Radio

Alternate Microphones and Installation

Fig. 2 Microphone cable preparation

Fig. 3 Microphone plug wiring

Fig. 4 Microphone plug pin numbers viewed from rear of pin receptacle

3

2

41

Your Mobile Radio

Alternate Microphones and Installation

To wire the microphone cable to the plug provided, proceed as follows:

1.Remove the retaining screw.

2.Unscrew the housing from the pin receptacle body.

3.Loosen the two cable clamp retainer screws.

4.Feed the microphone cable through the housing, knurled ring and washer as shown Fig. 3B.

5.The wires must now be soldered to the pins as indicated in the wiring table.

If a vise or clamping tool is available, it should be used to hold the pin receptacle body during the soldering operation so that both hands are free to perform the soldering. If a vise or clamping tool is not available, the pin receptacle body can be held in a stationary position by inserting it into the microphone jack on the front panel. The numbers of the pins of the microphone plug are shown in Fig. 4, as viewed from the back of the plug. Before soldering the wires to the pins, pre-tin the wire receptacle of each pin of the plug.

Be sure that the housing and the knurled ring of Fig. 3 are pushed back onto the microphone cable before starting to solder. If the washer is not captive to the pin receptacle body, make sure that it is placed on the threaded portion of the pin receptacle body before soldering.

If the microphone jack is used to hold the pin receptacle during soldering operation, best results are obtained when the connections to pins 1 and 3 are made first and then the connections to pins 2 and 4. Use a minimum amount of solder and be careful to prevent excessive solder accumulation on pins, which could cause a short between the pin and the microphone plug housing.

6.When all soldering connections to the pins of the microphone are complete, push the knurled ring and the housing forward and screw the housing onto the threaded portion of the pin receptacle body. Note the location of the screw clearance hole in the plug housing with respect to the threaded hole in the pin receptacle body. When the housing is completely threaded into the pin receptacle body, a final fraction of a turn either clockwise or counterclockwise may be required to align the screw hole with the threaded hole in the pin receptacle body. When these are aligned, the retaining

screw is then screwed into place to secure the housing to the pin receptacle body.

7.The two cable clamp retainer screws should now be tightened to secure the

housing to the microphone cord. If the cutting directions have been carefully followed, the cable clamp should secure to the insulation jacket of the microphone cable.

8.Upon completion of the microphone plug wiring, connect and secure the microphone plug in the transceiver.

 

 

 

 

18 English

Nothing comes close to a Cobra® 19

Image 13
Contents GTL DX Our Thanks to You Our Thanks to You FCC License RequiredFCC License Required Controls and Indicators Controls and Indicators Microphone and FeaturesFeatures MicrophoneWarranty ContenProductsFeaturesIntroduction Your Mobile RadioSpecifications SpecificationsInstallation and Connection Installation and ConnectionIncluded in this Package Included in this PackageAntennas with adjustable screws setscrews 4Tuning the Antenna for Optimum SWR4Ignition Noise Interference 4AntennaControls Installation and Connection OperationOperation Controls4NB/ANL / ANL / Off 4Dim4Echo 4Talk BackFrequency FrequencyIndicators Indicators and Microphone Operating to Receive and TransmitOperating to Receive Operating to TransmitAlternate Microphones Installation Maintenance and Government Regulatory InformationMaintenance Alternate Microphones and InstallationAlternate Microphones and Installation Arrl Q Signals Arrl Q SignalsProduct Service Warranty and Trademark AcknowledgementLimited Two-Year Warranty Product ServiceOrder Form Optional Accessories AccessoriesAccessories Optional AccessoriesCobra line of quality products includes