Uniden DXAI4588 manual Important Safety Instructions, FCC Wants You To Know

Page 58

Important Safety Instructions

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:

1.Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.

2.Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.

3.Do not use the telephone to report a gas leak in the vicinity of the leak.

4.Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local authorities for possible battery disposal instructions.

5.Do not disassemble any component of this product.

SAVE THESE INSTRUCTIONS

CAUTION!

Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. Do not open or mutilate the battery, and disconnect the battery before shipping this product.

The FCC Wants You To Know

This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA.

On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US: AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.

An applicable Universal Service Order Codes (USOC) certification for the jacks used in this equipment is provided (i.e., RJ11C) in the packaging with each piece of approved terminal equipment. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA.

A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.

The REN is used to determine the number of devices that may be connected to a telephone

line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the telephone provider. For products approved after July 23,

2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g.,

03 is a REN of 0.3). For earlier products, the REN is separately

57

Page 57 Page 59
Image 58
Page 57 Page 59
Contents Page Contents Accessibility WelcomeTerminology Manual ConventionsAnswering Machine Features Main Phone FeaturesProduct Overview Controls and Functions HandsetsMain Base Unit Extra Charging CradleInstalling the Phone Choosing the Best LocationInstalling the Rechargeable Battery Packs into the Handsets Installing the Base Unit and Charging Cradle Page Mounting the Base Unit on a Wall Standard wall plate mountingDirect wall mounting Register Handsets to the Main Base before Using When to Re-register Handsets Basic Setup Activating AutoTalkActivating Caller ID on Call Waiting HS1 only Programming Your Area CodeChoosing the Dialing Mode HS1 only Setting the Language Using the Speed Dial Memory Storing a Name and Number in MemoryNumber of times key is pressed If you make a mistake while entering a name Storing Caller ID in Speed Dial Memory Making and Receiving Calls Using Your PhoneMaking a Call from Speed Dial Memory To cancel speed dialing Making a Call from the Caller ID ListTo transfer a call Transferring a CallTo receive a transfer call Redialing the Last Dialed Number Selecting the Ring Tone and VolumeAdjusting the Earpiece Volume Temporarily Mute RingerUsing Call Waiting Selecting a Different ChannelTone Dialing Switch-over Find HandsetCaller ID and Cidcw Caller ID on Call Waiting Caller ID on Call Waiting Cidcw Viewing the Caller ID Message ListDeleting all Caller ID names/numbers Deleting Information from the Caller ID ListDeleting a Caller ID message Press delete/transferFeatures Integrated Answering MachineSetting Up Your Answering Machine Answering Machine SettingSetting the Time Setting a Personal Security Code PIN Setting the Ring Time Selecting the Message Record TimeSetting the Message Alert Tone Preset message Setting Your Outgoing Message GreetingSelecting the Language Recording a personal outgoing message Greeting Choosing between the two outgoing messagesAdjusting the Speaker Volume Level Setting the Base Ringer VolumeTemporarily Mute the Base Ringer and Call Screen Using Your Answering Machine Turning the Answering Machine On/OffMessages Reviewing MessagesDay it was received Recording a Conversation Voice Memo Remote OperationPage Turn on the Answering Machine Remotely Changing the Digital Security Code Specifications MaintenancePower Failure Low battery alert Talk and Standby TimesBattery replacement and handling Cleaning the battery charging contactsSymptom Suggestion Charge/in use LED or TroubleshootingCommon Issues Traveling Out-of-RangeSymptom Suggestion Call was answered before the second ring Adjust the speaker volume on the base unit Liquid Damage Handset BasePrecautions Rechargeable Nickel-Cadmium Battery WarningImportant Safety Instructions FCC Wants You To KnowRadio Interference Shown on the labelTerminal Equipment Cordless Telephone PrivacyRadio Equipment One Year Limited Warranty O, P, Q IndexF, G, H, I, J, K, L X, Y, ZMemo Memo Remote Operation Card Remote Operation Card Memory Location MemoTask Key At Uniden, we’ll take care of you
Top Page Image Contents