Panasonic RX-EX1 operating instructions Cassettes, Before Recording

Page 15

PLAY	RE FADER SLEEP	EQ ON
1	REC	ALL 1-REC ST
PGM	RANDOM	MONO
Tape Counter		Tape Playing
PLAY	RE FADER SLEEP	EQ ON
1	REC	ALL 1-REC ST
PGM	RANDOM	MONO

Present state (e.g., elapsed play time of CD)

PLAY	RE FADER SLEEP	EQ ON
1	REC	ALL 1-REC ST
PGM	RANDOM	MONO
Present time
PLAY	RE FADER SLEEP	EQ ON
1	REC	ALL 1-REC ST
PGM	RANDOM	MONO
Tape counter
PLAY	RE FADER SLEEP	EQ ON
1	REC	ALL 1-REC ST
PGM	RANDOM	MONO

Cassettes

	Press [POWER,			] to turn the unit on.

	Insert a cassette into the deck.
	Play starts from the side facing up.
	Press [3 TAPE] to start play.				Listening
	Turn [– "VOLUME#+ ] to adjust the volume.

To stop play

Press [7 TAPE/CD].

To eject tape

Stop tape play, then press [0 TAPE].

One touch play (When using AC power)

When a cassette is loaded, press [3 TAPE].

The unit comes on and play starts.

Fast-forward and rewind

Press [REW/–/		] (rewind) or [		/+/FF] (fast-forward).
Press [REW/–/		] (rewind) or [		/+/FF] (fast-forward).
of these tapes.				Recording
Selection of tapes

Use normal position tapes to play correctly.

High position and metal position tapes can be played, but the unit will not be able to do full justice to the characteristics

Cassette tape care

•Tapes exceeding 100 minutes are thin and can break or get caught in the mechanism.

•Tape slack can get caught up in the mechanism and should be taken up before the tape is played.

•Endless tapes can get caught up in the deck’s moving parts if used incorrectly.

Before Recording

Use household AC power or new batteries when recording, to avoid poor recording caused by the batteries running down.

Television can cause interference to recording made on this unit if the two are too close to each others.

Selection of tapes for recording

Use normal position tapes.

High position and metal position tapes can be used, but the unit will not be able to record or erase them correctly.

Volume and sound quality in recording

•Recording level is set automatically.

•Recording are unaffected by changes to sound quality.

To display the tape counter while recording

Remote control only

Press [DISPLAY].

Each time you press the button in the CD or radio mode:

To reset the tape counter

Press [C-RESET].

The counter resets to “000”.

15

RQT5671

Image 15

Contents Portable Stereo CD System Supplied Accessories Dear customerRX-EX1 Table of contents Service SafetyInstallation MaintenanceListening caution Use of BatteriesBefore Power SourcesMemory Back-up Batteries UseCassette deck controls Location of ControlsBasic controls Tuner/CD controlsDo not Remote ControlButtons UseNot included Setting the TimeUsing Headphones MaintenanceListening CDsOther modes of play CDsFull is displayed To check the contents of the programProgram play Press CDRadio manual tuning Radio preset tuning Presetting radio stationsSelecting channels Before Recording CassettesRecording CDs RecordingBefore Recording To record a track in play Recording CDsInsert a cassette with the side for recording facing up If a track is interrupted at the end of the side fac Ing upSound Quality Recording the RadioHarmonic Enhancer Sound 3D sound with the Sound VirtualizerPress PLAY/REC to display the timer Indicator Using the TimerTimer Turning the timer onSleep Timer Timer FaderUsing the Timer Warranty U.S.A ReferenceOnly for U.S.A Specifications TroubleshootingProduct Service Product informationPuerto Rico contact the Panasonic Sales Company Tel.787 L1200GL1061 Panasonic Canada Inc