iHome iP99 IB Replacing iP99 Backup Batteries, Radio, Using the Line-in Jack, Using Sleep Mode

Page 7

Using the iP99

Radio

Setting up Antennas

a) Snap AM loop antenna into provided stand, then plug AM antenna cable into AM Loop Antenna socket on back of unit. Move antenna away from unit for best reception.

b) Extend FM Antenna (on back of unit) fully for best reception. Do not strip, alter or attach to other antennas.

c)Locate iP99 and all antennas away from AC adaptor in wall socket (at least 3 feet) for best radio reception.

Tuning and Playing the Radio

a)

Press the

Radio Button to select radio play mode. Press as needed to select FM or AM radio band.

b)

Turn the Set Wheel to tune radio to a desired station.

c)

To program

the current station as a preset, press and hold Preset Button 1-2 until P1 flashes on display; press again for P2

 

and allow to time-out (beep confirmation). Repeat steps a,b,and c for other preset buttons to preset up to 12 stations (6 AM, 6

 

FM). To listen to a preset station at any time, simply press the desired preset button once or twice.

d)

Turn the

Volume Wheel to adjust iP99 volume up or down.

e)

Press the

EQ Button to select Treble, Bass, SRS WOW sound effect or Balance. Turn the Set Wheel to adjust settings. EQ

 

settings for iPhone/iPod and radio mode are independent.

f)

Press Alarm Reset/Power Button to turn iP99 off.

Using the Line-in Jack

a) You can play nondocking iPod models or other audio devices through the iP99 Line-in Jack, connect one end of a patch cord (available at ihomeaudio.comin the device’s line out or headphones jack, the other in the iP99 line-in jack. Make sure there is no iPhone/iPod docked in the iP99 when using the line-in jack.

b) To listen to your audio device, press the Radio Button until “line-in” is displayed, indicating line-in mode. Adjust the output volume on your line-in device.

Using Sleep Mode

Sleep mode lets you sleep to your iPhone/iPod or the radio, gradually lowering the volume until the unit shuts off at the selected time.

a) Press the Sleep Button to select an amount of time before the iP99 shuts off: 120, 90, 60, 30 or 15 minutes.

b) Turn the Volume Wheel to set the sleep volume (this volume setting is separate from your standard volume setting).

Using the Dimmer

a) Press the Snooze/Dimmer Button during normal operation to adjust brightness of LCD display. There are 8 levels of brightness including OFF.

Replacing iP99 Backup Batteries

Install/Replace Backup Battery

The iP99 uses a backup battery system to provide continuous alarm operation and clock settings in the event of a power failure. If the Battery Low Icon located on the right of the display is on, it is time to replace the backup batteries. Please make sure the AC adaptor is connected, otherwise all settings may be lost during battery replacement.

Open the battery compartment cover located on the bottom of the unit. Insert 2 “AA” batteries as indicated. We recommend the use of alkaline batteries for longer life.

Batteries information:

• Do not mix old and new batteries.

• Do not mix alkaline, standard (carbon -zinc) or rechargeable (nickel-cadmium) batteries.

5

Image 7
Contents Home System For Your iPhoneor iPod Maintenance Table of ContentsRisk of Electric Shock Do not Open IP99 quick start Rear Panel Controls and IndicatorsIP99 display Top PanelConnect iP99 to Power Source Using the iP99Using the Dimmer Replacing iP99 Backup BatteriesUsing the Line-in Jack Using Sleep ModeInstalling/Replacing the Remote Control Battery Using The Remote ControlSymptom Possible Problem Solution TroubleshootingNoisy Síntoma Causa Solución Solucionando problemasLa banda de AM se La antena circular no está ubicada Consumer Guide to Product Safety Or call 1-877-446-6301 Toll Free Limited 1 Year Warranty Information