16. ON/OFF but TON Pitch, SAM. Button

16. ON/OFF BUT TON (PITCH)

Press the button to be PITCH ON mode, press it again on the PITCH ON mode, and blinks with unit on the PITCH OFF mode.

17. 3 HOT -CUE

This unit will allow you to play from 3 cue points instantly.

a . Set CUE memory: Press the MEMO button first, and then press the CUE button to complete the CUE setting, then this C UE button will light up .

b . Play” CUE” memory: Upon pressing specific CUE button, it will flash about 5 seconds.

Note: This function is not available during perform REV ERSE sound effect.

18. SAM. BUTTON

Sampler is a kind of sound effect that you record the music from the track. While playing the music, you can use the sampler to mix with music. The maximum length is 32 seconds.

a. Set start point: Press the MEMO key, and then press SAM button, after memorizing the SA M button flashes quickly (2 times in 1 sec)

b. Set End point: Press the SAM button again, when the end point is memorized, the S AM button lights up (not flash).

c. Play Sampler: During PLAY mode, press the SA M button, then the button will flash slowly. (1 time in 1 sec)

NOTE: Refer to parameter setting instruction for sampler adjustment

19. JOG WHEEL

*Speed Control (SEARCH indicator off)

Rotating the wheel, in play mode, will change the playback speed accordingly. While rotating clockwise, the player speed increase; rotating counterclockwise, the speed decrease.

*Search (SEARCH indicator lights)

Rotating the wheel, the player will forward or backward quickly. The searching speed changed according to the dialing speed. It can be carried out by one frame increment.

20. Seamless Loop (2 set)

There is A, B/LOOP/ EXIT, RELOOP buttons.

1 . A BUTTON---“start point” (A point. Also, Cue 1 could be A point) After setting up the A point, the red Led light up

2 . B/LOOP/ EXIT BUTTON: ---“ End point”(B point). Press the B /LOOP button to set up the B point and start the loop playback automatically. Loop lights on the display and the 3 LEDs flash. Press this button again to exit the LOOP playback.

3 . Return to the loop playback by pressing the RELOOP while in performance. However, if your want to return to loop playback, you can press RELOOP BUTTON

4 . Change “ START POINT” and” END POINT” by pressing the A& B/ LOOP/ EXIT button again

5 . The interval between A and B point must be more than 20 frames; otherwise, the B point will be canceled, then LOOP function disappear and LOOP fades on the display

21.SOUND EFFECT/ DIRECT ACCESS BUTTONS

* SOU ND EFFECT OFF

The buttons are direct access keys (0~9). To select the number of the track you would like to play.

* SOU ND EFFECT ON

The buttons is for sound effect control and it lights up when the sound effect be chosen and off when the button is pressed again.

NOTE: How to set up the parameter; please refer to parameter setting instruction. (Page7)

SCRATCH: Move the JOG Wheel backward or forward like scratching a turntable record. This sound effect can be performed independently, or in parallel with other effect.

BRAKE: To change the speed of PAUSE and START. This sound effect can be performed independently, or in parallel with other effect.

REVERSE: The music is playing backward. This sound effect can be performed independently, or in parallel with other effect. PHASER: It sounds like the airplane takes off

FLANGER: It sounds like another kind of airplane takes off. .

FILTER: There are bass & treble. To increase the parameter value, it will cut bass off but keep treble. To decrease the parameter value, it will cut treble off but keep bass.

CHOP: The music is chopped with break.

PAN: Alternatly playing right and left signal

ECHO: Have the effect as ECHO.

22.SOUND EFFECT ON/OFF SWIT CH

Press the EFFE CT button to activate or deactivate the sound effect. While the effect is activated, on the display the mark above the effect is light. .

23.EFFECT SELECT KNOB

The parameter of sound effect can be pre-set. Turn the knob until the LCD shows the effect name that you want, push the button to select it, and turn this button again to select from the menu for setting parameter.

24.EFFECT SCOPE KNOB

After the menu of effect is selected, turn this knob to choose the parameter, the relative value can be shown in the LCD.

(Please refer to page 7 with the Parameter Setting Instruction for details)

When the unit is not under parameter adjustment, the display does not show the effect name, this knob can be used to adjust the KE Y scale, and press it to lock the key (the display will show)

25.RELAY

Press the “RELAY” button to activate . When one unit is in play mode, and the other unit is in “pause” mode; pause the playing unit, the other unit will automatically start to play (the button will blink).

26.BPM BUTTON

You can get the BPM number automatically or manually. Pressing the BPM BUTTON for 3 seconds to switch between auto and manual control. The B EAT will be shown on the display! Under the manual mode, tapping this button to get the beat value .

27.KEY ON/OFF SWITCH

Press the button to switch KEY mode on or off.

KEY OFF: The display shows the “KEY” in blinking, and the key changed according to the pitch change. The key parameter adjustment is not in effect

KEY ON: The “KEY” lights on the display, turning the SCOPE knob to adjust the key. Slide the pitch slider will also change the key.

KEY LOCK: Press the SCOPE knob to lock the key as set,

sliding the pitch slider does not change the key. Please refer to parameter setting instruction. (Page 8)

28.CARD: Switch the playback source to memory card .

29.CONNECTOR PORT

The 8-pin(6 -pin) termination permits the connection of the control unit to the main unit.

30.SLEEP:

Leave the unit unused for 30 minutes; the machine will shut off automatically.

- 5 -