Panasonic SC-VKX60 operating instructions Changing the main unit and remote control mode

“AUDIO” menu

CURRENT SETTINGS	Show the current setting of the items in this menu.
PCM OUTPUT	UP TO 48kHz: When you connect to an equipment compatible with 44.1 kHz or 48 kHz.
Do a check on the digital input	UP TO 96kHz: When you connect to an equipment compatible with 88.2 kHz or 96 kHz.
limitations of the equipment you	• Signals from copy-protected discs are converted to 48 kHz or 44.1 kHz.
connect using COAXIAL terminal	• Some equipment cannot support sampling frequencies of 88.2 kHz, even if they can support
and select the maximum sampling	96 kHz.
frequency of PCM digital output.	Read the operating instructions of your equipment for details.
DOLBY DIGITAL	BITSTREAM
With COAXIAL connection (Z 19)	PCM	Select “BITSTREAM” when the equipment can decode the bitstream (digital form of
	BITSTREAM
DTS		multi-channel data). If not, select “PCM”. (If the bitstream output to the equipment
With COAXIAL connection (Z 19)	PCM	without a decoder, there can be high levels of noise output that can do damage to
		your speakers and hearing.)
MPEG	BITSTREAM
With COAXIAL connection (Z 19)	PCM
DYNAMIC RANGE	ON: Adjust for clarity even when the volume is low. The range between the lowest and the highest
	sound levels is compressed. Convenient for late night viewing. (Only works with Dolby Digital.)
	OFF
“DISPLAY” menu
CURRENT SETTINGS	Show the current setting of the items in this menu.
LANGUAGE	ENGLISH		FRANÇAIS	ESPAÑOL	DEUTSCH
Select the language for the on-screen	PУCCKИЙ		MAGYAR	ČESKY	POLSKI
messages.
“OTHERS” menu
CURRENT SETTINGS	Show the current setting of the items in this menu.
	SHOW CODE: You must have this registration code to purchase and play DivX Video-on-Demand
		(VOD) content (Z 23, “About DivX”).
REGISTRATION
	This item is only shown until you play a DivX VOD content or after you deregister this system.
Show the registration code of the
system.
	SET: You must have this deregistration code to cancel the registration of this system
	(Z 23, “About DivX”).
DEREGISTRATION
	This item is only shown after you play a DivX VOD content for the first time.
Show the deregistration code of the
system.
	To change the slideshow time
	1 SEC to 15 SEC		15 SEC to 60 SEC	60 SEC to 180 SEC
SLIDE SHOW TIME
	(in 1-unit)		(in 5-unit)	(in 30-unit)

• “3 SEC” is the factory preset.

EASY SETUP	SET: Shows the EASY SETUP settings.
DVD-VR/DATA	DVD-VR:To play video on DVD-R/RW.
Select to play only DVD-VR or DATA	DATA: To play data files on DVD-R/RW.
format.
SCREEN DIMMER	OFF
This is to prevent burnt mark on the	WAIT 5 MIN: If there is no operation for 5 minutes, the picture becomes grey. The TV screen will
TV screen.	go back to the normal position when you do some operations. (This does not apply
	during video playback.)
DEFAULTS	RESET
This returns all values in the SETUP	The password screen is shown if “RATINGS” (Z 20) is set. Input the same password and press [OK],
menus to the default settings.	then switch off the system and switch on again.

ENGLISH

OTHER OPERATIONS

Changing the main unit and remote control mode

You can change the remote control and main unit mode if the remote control operates other Panasonic equipment.

Make sure that the main unit and remote control have the same mode.

To set the mode to “REMOTE 2”

1 Press and hold [EXT-IN] on the main unit and [2] on the remote control until “REMOTE 2” is shown.

2 Press and hold [OK] and press [2] for a minimum of 2 seconds.

To set the mode to “REMOTE 1”

1 Press and hold [EXT-IN] on the main unit and [1] on the remote control until “REMOTE 1” is shown.

2 Press and hold [OK] and press [1] for a minimum of 2 seconds.

Note:

After you set the mode, you can continue to use the TV operation buttons on the remote control to operate a Panasonic TV (Z 8).

RQTX1215

21

21