Panasonic EP30007 operating instructions Attaching the control panel stand covers

Page 15

3 Attaching the control panel stand to the right or left side panel of the unit

(Diagram shows attachment to right armrest.)

1.Insert the attachment screw into the lower hole first

The position of the control panel when seated can be

and then tighten lightly by hand.

selected by choosing the appropriate hole for the screw.

 

2.Securing the stand with the attachment screws.

Near

Approx.

Tighten the two screws for the remaining two holes

 

20˚

lightly by hand and then tighten firmly with the allen key.

 

 

Far

 

 

Control panel stand

 

 

 

2

 

 

1 Insert the attachment

 

 

 

screw in either hole and

 

To attach the control panel stand using the attachment

then tighten.

 

Attachment screw

Allen key

screws, tighten the screws level with the holes as

shown in the figure below.

 

 

 

 

Use this screw

 

If the screws are tightened at an angle, the hole may

 

become deformed and the screws may become stuck in

Attachment Screw (M6 × 16)

 

 

the middle.

 

 

 

Control panel

 

 

 

× 3

 

Control panel stand

stand

 

 

 

Hole

Attachment screw

Attachment

 

Hole

screw

 

Allen key

Allen key

 

 

 

Tighten the screws

Do not tighten the

 

screw at an angle

 

level with the holes.

 

with the hole.

 

 

4 Attaching the control panel stand covers

(On both the right and left sides)

The method for attaching the covers is the same for both sides. The diagram shows the side where the control panel stand is attached.

Cover for Side WITH

Cover for Side WITHOUT

Control Panel Stand

Control Panel Stand

1.Insert the top tabs on the cover into the bottom notches on the armrest.

Notches

2.Insert the bottom tabs into the notches on the armrest.

Bottom tabs

 

Control panel

 

stand cover

Top tabs

Notches

Push the cover until you hear it click.

12

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Operating Instructions Instrucciones de Uso Page Index Important Safety Instructions Safety Precautions Operating Precautions Grounding Instructions Main unit Part names and functionsBack Control Panel Ultra Knead/Repeat Display Voice Guidance Volume DisplaySelf-Program Setting Display Time Remaining Display During massage To put the unit down on the floor Setting up the massage lounger Where to use the unit Removing everything from the box and installing the unitWidth Approx 68 cm Height Approx 66 cm Length Approx 160 cm AccessoriesAssembly Connecting the air plugsAttachingarmrests Attaching the control panel stand covers Gap Flat-tip Screwdriver When removing the control panel stand coverConfiguration Raising the backrest to the upright positionPlacing the control panel into the control panel stand Attach the pillow to the velcro fasteners Inserting the shoulder plateAttaching the pillow Shoulder plate PocketCheck the unit Check the power cord and the power plugSwitching on the power supply Before sitting downWhen the massage heads are not in the retracted position Press one of the flashing buttons To select Program Press the button to turn on the powerPre-Program and Quick Massage Characteristics Upper Body Program MassagesBody scanning will commence when the program is selected During a massage When the massage startsOverview of the Pre-Program and Quick Massage Upper Body Self-Program Creating Self-ProgramsOpen the right cover and press the button Self-ProgramMassage Sequence Setting the Time and IntensityPress the button to start the program To change the time and intensity in the middle of a massageManual Selection Massages Manual OperationManual Operation Body scanning for Manual Operation Select the location you want to massageSelect the massage action Press the button to start the actionUltra Knead Shiatsu Swedish For additional operationsChanging the massage style Adjustments During a MassageAdjusting the speed Changing the programAdjusting the position Adjusting the intensityRange that can be massaged on the upper body Width Adjustment LimitsAdjustment of range of intensity Details about the massage styleAdjusting the intensity Open the left coverTo execute the air massage only Adjusting the Legrest length Adjust the legrest so that your feet fit snuglyFor the foot reflexology plate How to use the hand/arm massage Arm MassageInsert the hand all the way inside Center of the armrest Adjustments for the Shoulder Massage Adjustments for the seat/thigh massageOuter Shoulder Massage To execute the stretch massage only Using the stretch massageOperations of the leg stretch Operations of the arm stretchOttoman and Backrest height adjustment Legrest slide lever Adjusting the voice guidance volume Press Button to adjust the volumePress the button to shift the volume level by one up/down Adjusting the control panel stand and pillow Adjusting the control panel standAdjusting the pillow for correct height during a massage Advanced user memory function Saving the user program settingsWhen the selected button starts flashing quickly Press the button used to save your settingsFor Pre-Program, Quick Massage, and Self-Program Settings that can be savedLeg stretch settings Leg stretch settings Air massage settingsErasing saved data Press the button to turn on the power When the massage is complete After completing the massageEmergency Stop Press the button Keep the lock switch key out of reach of children Disconnecting the powerCleaning and Maintenance Areas covered with synthetic leatherWipe these areas with a soft, dry cloth Panel on the seat Moving the UnitLifting the Unit Do not move the unit while someone is seated in itUsing the wheels to move the unit Neck Problem Cause and Remedy Motor NoisesMassage heads stop during operation Massage heads do not come up to the shoulder orPower cord or power plug is abnormally hot Problem Cause and Remedy Unit will not operate at allSometimes the power won’t turn on when Is pressed Again when a massage has finishedPanasonic Consumer Electronics Company
Top Page Image Contents