Wall and Stand Placement, Exploded

WALL AND STAND PLACEMENT

Adjustable wall brackets are included for the two speakers and transmitter module. The included bracket are for wall-mounting only. It is not to be used for ceiling mounting. Ceiling mounting of the Control 2.4G AW transmitter and/or speakers is not recommended, regardless of bracket used.

Wall-Mounting the Speakers

Using Wall Brackets Provided

Important safety note: Proper selection of mounting hardware not included herein, and proper assembly and installation of brackets, including, but not limited to, selection of appropriate weight-bearing support and bracket use with the specified speaker only is the exclusive responsibility of the customer. Manufacturer disclaims any liability for the selection of mounting hardware and/or bracket installation.

Exploded
– +	– +
TO LEFT SPEAKER	TO LEFT SPEAKER
CORRECT	INCORRECT

English

A. Loosen and remove the molded nut (2) by turning it counter clockwise. Use the supplied metal bar (5) if necessary by inserting it in one of the holes on the molded nut (2).

B. Pull the ball/shaft (3) out of the wall bracket (4).

C. Slide on the molded nut (2) onto the ball/shaft (3) with threaded opening facing the ball, and thread on the metal nut (1) all the way onto the ball/shaft (3), with the nut’s (1) ”knurled” surface facing away from the ball.

D. Screw on the ball/shaft (3) into the threaded 1/4"-20 insert on the back of the speaker cabinet (6) until it is fully seated against the bottom of the insert. Back out the ball-shaft assembly 1/2 of a turn and tighten the nut against the speaker. If the ball and shaft assembly is not backed out before tightening the nut, performing Step G below may dislodge the threaded insert in the speaker housing and permanently damage the speaker.

E. Tighten the ”knurled” nut (1) using a crescent wrench until it is firmly seated against the back of the speaker and has fully locked the ball/shaft (3) and the speaker cabinet together. Pleace note that once this nut is tightened, it may embed some marks on the back of the speaker where the attachment is made. However, these marks will be covered by the nut (1).

F. The back-up cord (8) is provided as an additional measure to prevent the fall of the speaker in case the speaker becomes detached from the wall bracket.

One of the two lower screws (9) that attach the wall bracket (4) to the wall will need to go through the eyelet (11) at the end of the cord before going through the wall bracket hole. Mount the wall bracket

(4)onto a wood stud on the wall, using #10, minimum 1-inch-long, panhead wood screws. Make sure that all 4 screws are driven into the stud, not drywall. If the bracket needs to be mounted on drywall, the use of properly selected and installed wall-anchors and screws is essential. Make sure that the screw head is at least 9mm (0.36 or approximately 3/8 of an inch) or larger in diameter so that it can properly hold the backup cord eyelet (11).

G. Holding the speaker cabinet (7) with both hands, reinsert the ball portion of the ball/shaft (3) into the wall bracket (4).

H. Hand-tighten the molded nut (2) while positioning the speaker for the intended orientation.

I.Once the orientation of the speaker is finalized, use the metal bar

(5)in one of the holes on the molded nut (2) and tighten securely.

J.Securely attach the other end (10) of the backup cord (8) to the Control 2.4G, by engaging it through the bar (12) on the back speaker.

Also included with the system is a wall-mount holder for the active speaker’s power supply. If desired, you may attach this holder to the wall and insert the speaker’s power supply.

Please note that while the Control 2.4G AW is an all-weather outdoor loud-speaker, it is not waterproof. Neither the speakers nor power supply should be submerged or directly exposed to water, ice, snow or sustained moisture.Do not install the transmitter module outdoors.