Heat Controller EKTC, EKTH Proper Sleeve Tilt, Cabinet Front Removal View, Front Mounting Screw

Page 8

Installation Instructions

SLEEVE INSTALLATION

In order for condensate water to drain properly inside the unit, the sleeve must be installed properly:

Level from right to left.

A slight downward pitch from the indoor side to the outdoor side as shown below.

Refer to the Installation Instructions supplied with the PTAC wall sleeve for a complete description of the installation procedure.

Inside

 

 

 

 

 

 

 

 

 

 

Outside

 

 

 

 

 

 

 

Level

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Wall

 

 

 

 

 

 

1/4 Bubble

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Tilt To

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Sleeve

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Outside

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Outside

Wall

Proper Sleeve Tilt

OUTDOOR GRILLE

An outside grille must be installed to direct air flow for proper unit operation and also protect the outdoor coil. The grille must be installed before installing the chassis. Refer to the Installation Instructions supplied with the outdoor grille kit for a complete description of the installation procedure.

This model requires either a Stamped Grille Kit (Model SGK--B), a Polymer Grille Kit (Model PGK) or an Architectural Grille Kit (Model AGK--B). When replacing an old chassis with an existing grille or using a specialized grille in a new installation, please check with your sales representative to determine if the new chassis should be used with the non-standard specialized grille. An improper outdoor grille can decrease cooling or heating capacity, increase energy usage and shorten compressor life and possibly void the warranty.

FRONT REMOVAL

1.Grasp the cabinet front.

Cabinet Front Removal View 1

2.Pull the bottom of the cabinet front away from the chassis until the retaining clips disengage. NOTE: If front is secured with screws, remove front mounting screw, then follow front re- moval procedure.

Cabinet Front Removal View 2

Front Mounting

Hole

Front Mounting Screw

3.Lift the cabinet front off the chassis. Reverse this procedure to reinstall the cabinet front.

CHASSIS INSTALLATION

1.Remove the cabinet front from the chassis as described in Front Removal.

2.Insert the chassis into the wall sleeve.

Wall Sleeve

Chassis

 

 

 

Outside

Slide Chassis In

Wall

 

 

 

Chassis Installation View 1

3.Slide the chassis into the wall sleeve until the chassis flanges contact the front edge of the wall sleeve.

7

Image 8
Contents EKTC/EKTH Package Terminal AIR CONDITIONER/HEAT Pump Recognize this Symbol AS a Safety Precaution Unit Features Lcdi power CordTouch Pad Control Panel Chassis FrontEnergy Management System Features Unit Accessories Transportation DamageInstallation Instructions Sleeve Stiffener and Rear Closure Panel RemovalChassis Installation View Proper Sleeve TiltCabinet Front Removal View Front Mounting ScrewHeaterless Units WiringPtac Wire Harness KIT PWHK01C Power Cord Requirements Operating InstructionsOperating Voltage User ControlsControl Board User Inputs Maximum Wire Length for Front Desk SwitchFront Desk Switch Wiring Schematic Low Voltage Wires Routing Vent Door Lever PositionsVent Control Lever Discharge Grille Orientation OptionsRemote Thermostat Remote Control InputsDischarge Air Flow Grille Removal Maximum Wire Length for Remote Control Connection Wiring Schematic for Straight Cool UnitWiring Schematic for Remote Heat Pump Maintenance and Cleaning Monthly Maintenance and CleaningIntake Filter Removal Vent Left Side UnitYearly Maintenance and Cleaning Cabinet FrontObtaining Service Normal Operating Sounds and ConditionsConfiguration Settings To exit configuration modeDiagnostic Maintenance & Status Report Diagnostic Status Report ModeOperating Temperatures Active FailuresDiagnostic Codes 12/06

EKTC, EKTH specifications

The Heat Controller EKTH and EKTC models are advanced heating solutions designed to provide energy-efficient climate control for residential and commercial spaces. These heat pumps combine sophisticated technology with user-friendly features to create a comfortable environment regardless of the outside temperature.

One of the standout features of both the EKTH and EKTC units is their inverter technology. This technology allows the compressor to operate at variable speeds, adjusting its output according to the current heating requirements. As a result, these systems provide consistent heating while consuming less energy compared to traditional fixed-speed units. The inverter technology not only enhances efficiency but also minimizes noise levels, making these heat controllers suitable for quiet environments.

Another significant characteristic of the EKTH and EKTC models is their all-weather performance. These heat pumps are engineered to perform effectively in a wide range of temperatures, ensuring reliable heating even in extremely cold conditions. With advanced defrost technology, these units can operate efficiently without freezing, maintaining optimal performance year-round.

User convenience is also a priority with the EKTH and EKTC systems. Both models feature intuitive digital controls that enable users to set their desired temperature comfortably. Additionally, many versions include Wi-Fi connectivity, allowing for remote access and control through a smartphone app. This feature is ideal for individuals seeking to monitor or adjust their heating systems while away from home.

Energy efficiency is a key aspect of the EKTH and EKTC heat controllers. They are designed with high Seasonal Energy Efficiency Ratios (SEER) and Heating Seasonal Performance Factors (HSPF), which indicate their effectiveness in converting energy into heated air. Energy Star certification is often achieved by these models, making them attractive options for energy-conscious consumers looking to reduce their carbon footprint.

With a compact design, the EKTH and EKTC units can be easily integrated into various settings without taking up much space, allowing for flexible installation options. The sleek aesthetic also ensures that they blend seamlessly with interior decor.

In summary, the Heat Controller EKTH and EKTC models represent a cutting-edge solution to heating needs. They combine inverter technology, all-weather performance, user-friendly features, and high energy efficiency to provide reliable and comfortable heating solutions for any environment. Whether for a home or a commercial space, these heat pumps deliver quality and convenience in climate control.